Yamaha DSP5D - Manual (Page 210)

UTILITY function
210
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section
Note
During PREVIEW mode, the following USER DEFINE functions that affect internal signal processing are disabled;
EVENT LIST, TALKBACK ASSIGN, MONITOR, MIDI DIRECT OUT, MACHINE CONTROL, and GPI OUT CONTROL.
SET NOMINAL
LEVEL
— —
If you hold down this key and press the [SEL] key, the fader
of that channel will be set to nominal level. (While you hold
down this key, only the [SEL] keys of channels not at nominal
level will light.) Alternatively, you can set the level to nominal
level by moving the cursor to an on-screen knob (level, EQ
gain) or fader, and then pressing the [ENTER] key while
holding down this key.
SET DEFAULT
VALUE
— —
If you move the cursor to an on-screen knob or fader, and
then press the [ENTER] key while holding down this key, the
control will return to its default value
ENCODER MODE
KEY
PAN
—
Same function as the [PAN] key in the top panel ENCODER
MODE section
GAIN/ATT
Same function as the [GAIN/ATT] key in the top panel
ENCODER MODE section
ALT LAYER
Same function as the [ALT LAYER] key in the top panel
ENCODER MODE section
MIX SEND 1–24
Same function as the MIX SEND SELECT [1]--[24] keys in
the top panel ENCODER MODE section
FADER FLIP —
Same function as the [FLIP] key in the top panel FADER
FLIP section
SELECTED CH INSERT ON/OFF — Turns insert on/off for the selected channel
STEREO STRIP
SECTION
STEREO A, STEREO B MONITOR, CUE
Select either STEREO A/B channels, Monitor, or Cue as the
function controlled by the STEREO A/B channel strip's STE-
REO fader and [ON] key
Dark: Monitor or CUE is enabled
Lit: STEREO A/B channels are enabled
DSP5D CONTROL
MACHINE SELECT
#1(PM5D), #2(DSP5D),
#3(DSP5D)
Select the PM5D or DSP5D (#2 or #3) as the machine that
will be controlled by panel operations (Lit if the specified
machine is selected)
CH STRIP LAYER DIRECT
#1(PM5D) CH1-24,
#1(PM5D) CH25-48,
#2(DSP5D) CH1-24,
#2(DSP5D) CH25-48,
#3(DSP5D) CH1-24,
#3(DSP5D) CH24-48,
#1(PM5D) STIN1-4,
#1(PM5D) FX RTN1-4,
#2(DSP5D) STIN1-4,
#2(DSP5D) FX RTN1-4,
#3(DSP5D) STIN1-4,
#3(DSP5D) FX RTN1-4
Switch the INPUT channel strip or ST IN/FX RTN channel
strip to a layer of the desired machine (Lit if the specified
layer is selected)
*1. The corresponding channel will be selected in the DEFINE field of the MONITOR screen, and the monitor source will switch to
DEFINE.
*2. The LED will light for User Defined keys for which a screen has been memorized. The column in the right of the list in the USER
DEFINE screen shows the name of the memorized screen.
*3. Layers that can be memorized include the following items.
- The layer selected in the INPUT channel strip (CH 1-24, CH 25-48, MIDI REMOTE)
- The layer selected in the ST IN/FX RTN channel strip (ST IN 1-4, FX RTN 1-4, MIDI REMOTE)
- The layer shown by the DCA channel strip (DCA, A–F, GEQ)
- If the DCA channel strip is controlling GEQ, the GEQ module number and band
- The encoder mode selected by ENCODER MODE (SEND, PAN, HA, ATT, ALT)
- The FADER FLIP status
- The currently selected MIX send
- The mode selected in the MIX section (MIX SEND, MIX MASTER)
- The source selected in the METER section (CH 1-24 ST IN, CH 25-48 ST IN, MIX/MATRIX)
*4. The output port and MIDI channel can be specified in the MIDI SETUP screen.
*5. This parameter specifies the PM5D Editor window that you want to control. If the specified window is closed or inactive, the window
will be opened and made active. If the specified window is already open and active, the window will be closed.
FUNCTION PARAMETER 1 PARAMETER 2 Explanation