Yamaha DSP5D - Manual (Page 306)

PAN/ROUTING function
306
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section
B SEND LEVEL, PRE/POST (Send level / Send
point)
Select one of the following two parameters to view in
the grid.
❏ When the SEND LEVEL button is on
The send levels of the signals sent from input channels
to MIX buses are shown in the grid as bar graphs.
Except for the fact that the send-sources are input
channels and the send-destinations are MIX buses, the
bar graph display is the same as in the MIX to
MATRIX VIEW screen (MATRIX/ST function)
(
➥ p.264).
Depending on the send location of the signal being sent
to the MIX bus, the color of the bar graph will differ as
follows.
(green) . . . . PRE EQ (immediately before
the EQ)
(yellow) . . . PRE FADER (immediately
before the fader)
(blue) . . . . . POST ON (immediately after
the [ON] key) or POST TO ST
(immediately after the [TO ST]
key)
To edit the send level of a signal, move the cursor to
the grid where the desired channel and MIX bus inter-
sect, and turn the [DATA] encoder. To switch a MIX
send on/off, click the grid where the desired channel
and MIX bus intersect.
If the SEND LEVEL button is on, you can select a
desired grid and copy its send level (pan) value to other
channels (horizontal direction) or to other MIX buses
(vertical direction), or switch all grids on/off
simultaneously.
To do so, move the cursor to the desired grid; then
hold down the [SHIFT] key and press the [ENTER]
key. (Alternatively, hold down the [SHIFT] key and
click the desired grid.) When the following window
appears, select one of the following choices to copy,
and click the OK button.
LEVEL COPY [ALL MIX ]
Copy the send level (pan) value of the selected grid to
all MIX buses.
LEVEL COPY [ALL CH ]
Copy the send level (pan) value of the selected grid to
all input channels.
LEVEL COPY [ALL CH x ALL MIX]
Copy the send level (pan) value of the selected grid to
all input channels / all MIX buses.
ALL OFF [ALL MIX ]
Turn off the signals sent from the specified input
channel to all MIX buses.
ALL ON [ALL MIX ]
Turn on the signals sent from the specified input
channel to all MIX buses.
ALL OFF [ALL CH ]
Turn off the signals sent from all input channels to
the specified MIX bus.
ALL ON [ALL CH ]
Turn on the signals sent from all input channels to
the specified MIX bus.
ALL OFF [ALL CH x ALL MIX]
Turn off the signals sent from all input channels to all
MIX buses.
ALL ON [ALL CH x ALL MIX]
Turn on the signals sent from all input channels to all
MIX buses.
❏ When the PRE/POST button is on
This screen shows the send positions of the signals sent
from the input channels to the MIX buses.
Each indication has the following significance.
(green) . . . PRE EQ (immediately before
the EQ)
(yellow) . . PRE FADER (immediately
before the fader)
(gray) . . . . POST ON (immediately after
the [ON] key)
(red) . . . . . POST TO ST (immediately after
the [TO ST] key)
To change the send position of a signal, move the cur-
sor to the grid where the desired channel and MIX bus
intersect, and press the [ENTER] key, or click, or turn
the [DATA] encoder.
If the PRE/POST button is on, the send position for all
grid locations can be changed simultaneously. To do
so, hold down the [SHIFT] key and click the desired
grid. (Alternatively, move the cursor to the desired
grid; then hold down the [SHIFT] key and press the
[ENTER] key.) When the following window appears,
select one of the following choices and click the OK
button.