Recording, Manual edit recording, Follow steps 3–5 on page 28 – Yamaha GX707 User Manual

Page 40: Time

Advertising
background image

E

-30

Recording

Manual EDIT recording

You can program tracks manually while watching the remaining
time on both sides of the tape.

1

Press

INPUT

or

repeatedly until “CD” (1) appears on the

display, and load a disc (or discs) on the disc tray.

2

Follow steps 3–5 on page 28.

3

Press

PROG

.

* “PROG” and “P-01” will light up on the display, and all track

numbers on the selected disc will begin blinking.

4

If necessary, select the desired disc by pressing

DISC SKIP

.

5

Select the desired track number by pressing the numeric buttons.

6

Repeat steps 4 and 5 to program more selections for side A of
the tape. You can select the same track again.
* Pressing

TIME

displays the total remaining time on side A of

the tape for about 1 second, and then it is replaced by the
display of the next play order.

* You can only select track numbers 1 through 15 for manual

EDIT recording. All track numbers higher than 15 i.e.16, 17,
18… cannot be selected for recording even if there is
recordable space available on the tape.
“TM OVER” will appear on the display.
At this time, however, if any other track number is flashing
continuously on the display, you can program it instead of the
unprogrammable one.

7

When the programming for side A is finished, press

R. TIME

.

* “Side–B” appears on the display. You can begin programming

for side B.

* After following this step, you can check the programmed

contents for side A and side B alternately by pressing

R.

TIME

at any time before you press

EDIT

in step 9.

* The tape side indicator (9) shows the programming side

currently selected.

8

Repeat steps 4 and 5 to program selections for side B of the tape.
You can select the same track again.

9

Press

EDIT

. (“EDIT” (8) lights up on the display.)

The recording begins.

Note

To check, cancel or correct program data, refer to page 16.

To cancel the EDIT function

Before recording, press on the CD player or the tape deck.

To stop recording

Press on the tape deck.
(At this time, disc play automatically stops.)

Notes on recording with the EDIT function

• The maximum number of tracks that can be programmed is 20.
• The track number 16 or higher cannot be programmed by this

function.

• The CD player’s repeat play mode will be canceled during the

recording mode.

Display information during programming

STANDBY

/ON

STANDBY

TIMER

PROGRAM

B.BOOST

MUSIC

INPUT

PRESET/TUNING/BAND

A/B/C/D/E

/

VOLUME

UP

DOWN

DIRECTION

PHONES

BASS

TREBLE

MODE

DOLBY NR

REC/

PAUSE

AUTO/

MANUAL

TIMER

MEMORY

TIME ADJ

RANDOM

HOUR

REPEAT

TIME

DISPLAY

MIN

1

TIME

PROG

V

A

OVER 15

1 2 3 4
7 8 9 10

13 14 15

5

11

6

12

TRACK

CD

NR

PROG

V

A

OVER 15

1 2 3 4
7 8 9 10

13 14 15

5

11

6

12

REM

TRACK

CD

NR

Programmed track numbers light up and
only programmable track numbers
among unprogrammed ones flash.

Selected track
number

Total remaining time on
this side of the tape

Selected disc

Next play order

Side of the tape

POWER

1

1

2

2

3

3

4

4

5

5

6

6

7

7

8

8

9

0

PRESET

TUNER

+I0

PRESET

TIME

A

PROG

B

R.TIME

C

EDIT

D

DISC SKIP

MODE

E

CD

/

DIRECTION

LEVEL

REC/ PAUSE

TEST

PROGRAM

CENTER/

REAR/ DELAY

MUSIC

SLEEP

INPUT

TAPE

VOLUME

1

4

3

7

9

TIME

5

Advertising