Pioneer DJM-700-S - Manual (Page 18)

EFFECT FUNCTIONS
18
En
PRODUCING BEAT EFFECTS
Beat effects allow the instant setting of effect times in synch with
the BPM (beats per minute), thus allowing the production of a
wide variety of effects in synch with the current rhythm, even
during live performances.
1 Set BPM measuring mode to AUTO to measure BPM (beats
per minute).
The BPM of the input music signal is detected automatically.
Whenever power is first turned ON, the function defaults to the
[
AUTO ] mode.
• In the event the track’s BPM cannot be detected
automatically, the display’s BPM counter will flash.
• Measurable range: BPM=70 to 180.
It may not be possible to measure some tracks
accurately.
In this case, press the TAP button and input the beat
manually.
[Using the TAP Button for Manual BPM Input]
If the TAP button is tapped two times or more in synch with
beat (1/4 notes), the BPM will be recorded as the average value
recorded during that interval.
• When BPM mode is set to [ AUTO ], tapping the TAP button
will cause the BPM mode to change to the TAP mode, and
the interval at which the
TAP button is pressed will be
measured.
• When the BPM is set via the TAP button, the beat multiple
becomes “ 1/1 ” (or “ 4/1 ”, depending on the effect selected),
and the time for 1 beat (1/4 notes) or 4 beats will be set as
the effect time.
• If the TIME dial is rotated while depressing the TAP button,
direct BPM can be set manually.
If the
TIME dial is rotated while holding the TAP button and
AUTO buttons depressed, the BPM can be set in 0.1 units.
2 Set the effect selector to the desired effect.
• The display will show the name of the selected effect.
• See P. 16 to 17 for details regarding the various effects.
3 Set the effect channel selector to the channel you wish to
apply the effect to.
• The selected channel lights in the display’s channel name
area.
• If [ MIC ] is selected, the effect will be applied to both
microphone 1 and microphone 2.
4 Press the BEAT button ( , ) to select the beat multiple to
which the effect is to be synchronized.
• When is pressed, the beat count calculated from the BPM
is doubled, and when is pressed, the beat count
calculated from the BPM is halved (some effects also allow
“
3/4 ” setting).
• The multiple of the selected beat (parameter 1 position) is
displayed in seven sections on the display (see P. 12).
• The effect time corresponding to the beat’s multiple is set
automatically.
Example: When BPM = 120
1/1 = 500 ms
1/2 = 250 ms
2/1 = 1 000 ms
5 Set the ON/OFF button to ON to enable the effect.
• Each time the button is pressed, the effect alternates ON/
OFF (whenever power is first turned ON, the function
defaults to OFF).
• The ON/OFF button flashes when the effect is ON.
Parameter 1
Rotating the TIME ( PARAMETER 1 ) dial adjusts the temporal
parameter (time) for the selected effect. (With some effects, this is
used for adjustments other than time parameters.)
See P. 20 for details regarding the effect on parameter 1 of rotating
the
TIME ( PARAMETER 1 ) dial.
Parameter 2
Rotating the LEVEL/DEPTH ( PARAMETER 2 ) dial adjusts the
quantitative parameter for the selected effect.
See P. 20 for details regarding the effect on parameter 2 of rotating
the
LEVEL/DEPTH ( PARAMETER 2 ) dial.
A B M
MIDI
BPM
%
mS
1 2 3 4
AUTO
TAP
Display example
Effect Name: DELAY
Effect Channel Select: CH 1
BPM value: 120 BPM
Parameter 1: 500 ms
Beat multiple: 1/1
1
4
2
3
5
TAP
AUTO
ON/OFF
TIME
LEVEL/DEPTH
BEAT 2, 3
01_DJM-700_En.book 18 ページ ２００７年７月１０日 火曜日 午後８時４１分