RAM Mount Lightning Connector Dock - Manual

PARTS INDEX:
A. TAB-TITE™ SPRING TRAY (QTY. 1)
B. TAB-TITE™ END CUP (QTY. 2)
(CUPS MAY VERY DEPENDING ON TAB-TITE™ VERSION)
C. #4 X 3/8” SHEET METAL SCREW (QTY. 10)
D. RAM MOUNTING HARDWARE PACK (QTY. 1)
ALIGN (B) END CUPS WITH HOLES ON EACH
END OF (A) SPRING TRAY. SECURE CUPS TO
SPRING TRAY USING (C) SCREWS.
DO NOT OVER-TIGHTEN SCREWS
A
B
C
D
RAM TAB-TITE™ ASSEMBLY INSTRUCTIONS
USE MOUNTING SCREWS AND NUTS
PROVIDED IN (D) HARDWARE PACK
TO ATTACH TAB-TITE™ TO YOUR
RAM MOUNTING SYSTEM. USE
APPROPRIATE LENGTH SCREW FOR
YOUR MOUNTING SYSTEM.
PARTS INDEX:
A. TAB-TITE™ SPRING TRAY (QTY. 1)
B. TAB-TITE™ END CUP (QTY. 2)
(CUPS MAY VERY DEPENDING ON TAB-TITE™ VERSION)
C. #4 X 3/8” SHEET METAL SCREW (QTY. 10)
D. RAM MOUNTING HARDWARE PACK (QTY. 1)
National Products, Inc. 8410 Dallas Ave S. Seattle, WA 98108
206-763-8361 www.rammount.com
ALIGN (B) END CUPS WITH HOLES ON EACH
END OF (A) SPRING TRAY. SECURE CUPS TO
SPRING TRAY USING (C) SCREWS.
DO NOT OVER-TIGHTEN SCREWS
A
B
C
D
RMR-INS-AC
USE MOUNTING SCREWS AND NUTS
PROVIDED IN (D) HARDWARE PACK
TO ATTACH TAB-TITE™ TO YOUR
RAM MOUNTING SYSTEM. USE
APPROPRIATE LENGTH SCREW FOR
YOUR MOUNTING SYSTEM.
National Products, Inc. 8410 Dallas Ave S. Seattle, WA 98108 206-763-8361 www.ram-mount.com
RMR-INS-TABD14
1. INSERT iPAD INTO HOLDER
(HOLDER DESIGN MAY VARY) 2. INSERT LIGHTNING CONNECTOR CABLE.
VERIFY THAT YOUR iPAD RECOGNIZES THE
CABLE AND IS PROPERLY CONNECTED.
3. ASSEMBLE SCREW & NUT, CLAMPING LIGHTNING CONNECTOR IN PLACE.
CHECK ASSEMBLY PERIODICALLY, RE-TIGHTEN SCREW AND NUT AS NEEDED.
INCLUDED WITH YOUR HOLDER:
#4-40 X 3/8” MACHINE SCREW (QTY. 1)
#4-40 NYLOCK NUT (QTY. 1)
LIGHTNING CONNECTOR
DOCK CONVERSION INSTRUCTIONS
National Products, Inc. 8410 Dallas Ave S. Seattle, WA 98108
206-763-8361 www.rammount.com
RMR-INS-TABD14
1. INSERT iPAD INTO HOLDER
(HOLDER DESIGN MAY VARY) 2. INSERT LIGHTNING CONNECTOR CABLE.
VERIFY THAT YOUR iPAD RECOGNIZES THE
CABLE AND IS PROPERLY CONNECTED.
3. ASSEMBLE SCREW & NUT, CLAMPING LIGHTNING CONNECTOR IN PLACE.
CHECK ASSEMBLY PERIODICALLY, RE-TIGHTEN SCREW AND NUT AS NEEDED.
INCLUDED WITH YOUR HOLDER:
#4-40 X 3/8” MACHINE SCREW (QTY. 1)
#4-40 NYLOCK NUT (QTY. 1)
LIGHTNING CONNECTOR
DOCK CONVERSION INSTRUCTIONS
National Products, Inc. 8410 Dallas Ave S. Seattle, WA 98108
206-763-8361 www.rammount.com
RMR-INS-TABD14
1. INSERT iPAD INTO HOLDER
(HOLDER DESIGN MAY VARY) 2. INSERT LIGHTNING CONNECTOR CABLE.
VERIFY THAT YOUR iPAD RECOGNIZES THE
CABLE AND IS PROPERLY CONNECTED.
3. ASSEMBLE SCREW & NUT, CLAMPING LIGHTNING CONNECTOR IN PLACE.
CHECK ASSEMBLY PERIODICALLY, RE-TIGHTEN SCREW AND NUT AS NEEDED.
INCLUDED WITH YOUR HOLDER:
#4-40 X 3/8” MACHINE SCREW (QTY. 1)
#4-40 NYLOCK NUT (QTY. 1)
LIGHTNING CONNECTOR
DOCK CONVERSION INSTRUCTIONS
National Products, Inc. 8410 Dallas Ave S. Seattle, WA 98108
206-763-8361 www.rammount.com
RMR-INS-TABD14
1. INSERT iPAD INTO HOLDER
(HOLDER DESIGN MAY VARY) 2. INSERT LIGHTNING CONNECTOR CABLE.
VERIFY THAT YOUR iPAD RECOGNIZES THE
CABLE AND IS PROPERLY CONNECTED.
3. ASSEMBLE SCREW & NUT, CLAMPING LIGHTNING CONNECTOR IN PLACE.
CHECK ASSEMBLY PERIODICALLY, RE-TIGHTEN SCREW AND NUT AS NEEDED.
INCLUDED WITH YOUR HOLDER:
#4-40 X 3/8” MACHINE SCREW (QTY. 1)
#4-40 NYLOCK NUT (QTY. 1)
LIGHTNING CONNECTOR
DOCK CONVERSION INSTRUCTIONS