RAM Mount RAM-B-309-2 - Manual

RAM-B-309-2 ASSEMBLY INSTRUCTIONS
Parts Index
A . MOTORCYCLE HANDLEBAR BASE (QTY. 1)
B. ½” LONG NYLON SPACER (QTY. 2)
D. 6MM X 55MM BUT HD DR STST MACH SCREW (QTY. 2)
E.1/4” STST LOCK WASHER (QTY. 2)
LOCATE THE BRAKE/CLUTCH RESERVOIR TO THE HANDLE BAR. ONCE LOCATED, YOU WILL SEE TWO SCREWS
HOLDING THE ASSEMBLY TO THE HANDLEBAR. DEPENDING ON YOUR MAKE AND MODEL, THESE TWO SCREWS MAY BE BEHIND A PIECE OF
PLASTIC OR METAL TRIM. IF SO, REMOVE THIS PIECE OF TRIM TO EXPOSE THE SCREW HEADS. IT IS SUGGESTED THAT PRIOR TO REMOVAL
OF THESE SCREWS, MARK THE LOCATION OF THIS ASSEMBLY ON THE HANDLE BAR FOR HORIZONTAL AND VERTICAL PLACEMENT. THIS
WILL HELP YOU PUT THE ASSEMBLY BACK EXACTLY WHERE IT BELONGS.
A
B
C D
E
National Products, Inc., 8410 Dallas Ave S., Seattle, WA 98108, (206) 763-8361 www.ram-mount.com
R MR-INS-B-309-2
F
G
H
F. RAM 1” BALL WITH 1/4”-20 THREADED HOLE (QTY. 1)
G.1/4”-20 X 5/8” FLAT HEAD SCREW (QTY. 1)
C. 1/4”-20 2” BUT HD HEX DR STST MACH SCREW (QTY. 2)
H. EXTERNAL TOOTH LOCK WASHER (QTY. 1)
LOCATE THE BRAKE/CLUTCH RESERVOIR ASSEMBLY ON YOUR MOTORCYCLE HANDLEBAR. YOU WILL SEE TWO SCREWS (DEPENDING ON YOUR MOTORCYCLE,
THESE SCREWS MAY BE LOCATED BEHIND A PLASTIC OR METAL TRIM. REMOVE THIS TRIM TO EXPOSE SCREW HEADS.) BEFORE REMOVING SCREWS, MARK
THE LOCATION OF THIS ASSEMBLY ON THE HANDLEBAR INCASE THERE IS A NEED TO REINSTALL IT FOR FUTURE USE.
1. REMOVE ONE OF THE SCREWS AND COMPARE THE THREAD TO (C or D) SCREWS PROVIDED. GATHER THE
2 MATCHING SCREWS, 2 SPACERS (B), AND 2 LOCK WASHERS (E)
2. PASS EACH (C or D) SCREW THROUGH (E) LOCK WASHER, AND INSERT THROUGH SLOTTED HOLES OF (A)
HANDLEBAR BASE. SCREW HEADS SHOULD BE VISIBLE WITH RAM LOGO.
3. POSITION (B) SPACERS OVER THREADS OF EACH SCREW, AND SET ASSEMBLY ASIDE.
4. REMOVE FINAL SCREW HOLDING YOUR ORIGINAL BRAKE/CLUTCH ASSEMBLY. HOLD ASSEMBLY TOGETHER
WHILE REMOVING TO AVOID LOSING COMPONENTS. SET ASIDE CLAMP AND FACTORY SCREWS.
DEPENDING ON THE MOTORCYCLE, FACTORY CLAMP MAY NEED TO REMAIN IN PLACE TO ACCOMMODATE
THE LENGTH OF SCREWS IN YOUR RAM MOUNT KIT.
5. CAREFULLY PICK UP YOUR RAM MOUNT ASSEMBLY, AND BY HAND, THREAD RAM SCREWS INTO THREADED
HOLES OF YOUR BRAKE/CLUTCH RESERVOIR ASSEMBLY.
6. TIGHTEN SCREWS USING ALLEN WRENCH UNTIL RAM MOUNT IS SECURE.
7. STORE ANY UNUSED COMPONENTS OR HARDWARE FOR POSSIBLE FUTURE USE.
TO INSTALL ADDITIONAL RAM BALL
*INSERT (G) SCREW THROUGH (H) TOOTH LOCK WASHER.
*POSITION (F) RAM BALL INSIDE HEX HOLE OF (A)
MOTORCYCLE BASE.
*THREAD (G) SCREW THROUGH (F) RAM BALL THREADING.
TIGHTEN WITH SCREWDRIVER UNTIL (H) TOOTH LOCK
WASHER BENDS WITH COUNTERSUNK HOLE BEHIND (A)
HANDLEBAR BASE.
A
C or D
C or D
B
E
E
B
G H
F
A