Astro Pneumatic 5820 Engine Transverse Bar with Support Arm - Manual

(3)
(3)
(2)
(2)
(1)
(1)
(4)
(5)
(5)
www.astrotools.com
Unpacking
When unpacking, check the parts diagram and part number listing
on page 2 to make sure all parts are included. If any parts are
missing or damage, please call your distributor.
•Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year (except where noted on our
price schedule) from the date of 1st use. Astro reserves the right to determine
whether the product failed because of defective material, workmanship or other
causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its
discretion, will repair products covered under this warranty free of charge. The
distributor should direct the original user to return the product (with the exceptions
listed below) with the distributor’s name, address, adequate proof of date of
purchase or a copy of warranty card, and a short note explaining the problem.
Failures caused by accident, alteration, or misuse are not covered by this
warranty.
•Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
•This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you. All claims must be sent to:
Astro Pneumatic Tool Company
372 Old US Highway 52 South
Mt. Airy, NC 27030
1 YEAR LIMITED WARRANTY
Product: 5820 Manual
Dimension: 8.5"x 11"/page
Date: 2007/08/15
Color: 5820
• Makes removal of transaxle easy by supporting
engine of front wheel drive vehicles
• Support Arm provides three point support
for off-center loads
• Includes 1/8" braided steel cables and
14" adjustable hooks
• Capacity: 700lbs.
• Weight: 21 lbs.
Call 1.800.221.9705 for questions concerning performance of the product
or other inquiries.
Page 2
5820
372 Old US Highway 52 South
Mount Airy, NC 27030
ENGINE TRANSVERSE BAR
WITH SUPPORT ARM
Black
ENGINE TRANSVERSE BAR WITH SUPPORT ARM
5820-A01
5820-A02
5820-A03
5820-A04
5820-A05
5820-A06
5820-A07
5820-A08
5820-A09*
5820-A10*
5820-A11*
5820-A12*
5820-A13*
5820-A14
5820-AHK Support Arm (Left)
Support Arm (Right)
Support Arm (Middle)
Leg
Sling
Big Slider
Small Slider
“ J ” Hook
Cap Screw(M10x110mm)
Cap Screw(M10x50mm)
Wing Nut(M10)
Hex Nut(M10)
Washer(For M10 Bolt)
Protection Plastic Bar
Hardware Kit (A09-A13)
1
1
1
1
2
1
1
2
1
1
1
3
5
2
1
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
ENGINE TRANSVERSE BAR
WITH SUPPORT ARM
OPERATING INSTRUCTIONS
1. Test lip structure (Fig. 1) strength to assure
adequate support prior to using this unit.
The lip structure surface must be flat in
order to prevent slippage of this unit. Mount
the Transverse Support Bar with Support Arm
on the area of the lip structure that is strongest.
2. Loosen the cap screw (Fig. 2) on the slide
for adjustment.
3. To line up
“ J ” hook (Fig. 3) with the engine bracket
slide and/or pivot the arm into position.
4. The leg (Fig. 4) of the Third Arm Support must be
on a solid surface at the front of the vehicle. Wing
nut and cap screw can be removed to adjust the
height of the leg into a leveled position.
5. Attach the engine to the Engine Transverse
Bar. Hook the “J” hooks through the
engine bracket. When no lifting eye
is available, place the 1/8 " braided
steel cable (Fig. 5) around the
engine and attach to the “J” hook.
If the engine sags once attached
to the Engine Transverse Bar,
adjust the “J” hooks.
5820-A01
5820-A02
5820-A03
5820-A04
5820-A05
5820-A06
5820-A07 5820-A08
5820-A09*
5820-A10*
5820-A11*
5820-A12* 5820-A13*
5820-A14
5820-A14
5820-A13*
5820-A12*
5820-A13*
5820-A12*
5820-A13*
5820-A08
5820-A13*
1. ALWAYS read, understand and follow all safety warnings and instructions
included with this unit to avoid property damage and/or injury to self and others.
2. ALWAYS use Third Arm Support when using this unit.
3. ALWAYS test lip structure strength to assure adequate support prior to using this
unit. The lip structure surface must be flat in order to prevent slippage of this unit.
4. ALWAYS eliminate sagging of engine/transaxle by tightening nut on top of “J” hook
after positioning cables/or “J” hook.
5. NEVER overload. Maximum rated capacity is 700lbs. Overloading can cause
property damage and/or personal injury.
6. NEVER use this unit for purposes other than its intended design. This unit
designed to be used as engine support bar when a transverse axle or transmission
is being worked on or removed.
7. NEVER permit any body part to be under a load suspended by lifting or support
device. Accidental slippage of a lifting or support device can result in property
damage and/or personal injury.
For Your Safety & To Prevent Injury
WARNING
* Please notice that Part number with an asterisk
5820-A09*, 5820-A10*, 5820-A11*, 5820-A12*, 5820-A13*
are only available in the Hardware Kit 5820AHK
and are Not sold separately.