Astro Pneumatic 8202 Universal Welding Cart - Manual

Product: 8202 Manual
Dimension: 8.5"x 11"/page
Date: 2008/04/15
Color:
Black
Page 1
8202
Important
When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
www.astrotools.com
Product Information
• Heavy duty steel construction
• Heavy duty wheels - two 7.5" solid wheel and two 3" Swivel
• 3 shelves for easy access to supplies
• Cart size: 27-1/2"(L) x 16-1/3"(W) x 28"(H)
• Top shelf size: 17-3/4"(L) x 11-1/2"(W)
• Bottom shelf size: 27-1/2"(L) x 11-1/2" (W)
• Weight Capacity: 176lbs. Approximately
•Astro Pneumatic Tool Co. warrants our products to the original user against
defective material or workmanship for a period of 1 year from the date of 1st use.
Astro reserves the right to determine whether the product failed because of defective
material, workmanship or other causes and to charge back for missing parts. Astro
Pneumatic Tool Co., at its discretion, will repair products covered under this warranty
free of charge. The original user is to return the product (with the exceptions listed
below) with the distributor’s name, address, adequate proof of date of purchase or a
copy of warranty card, and a short note explaining the problem. Failures caused
by accident, alteration, or misuse are not covered by this warranty.
•
If one part of this product fails, please do not return the entire product.
Astro will replace free of charge component parts of this product that fail
within 1 year of first use by the original user. Items included in this category
include but are not limited to kits, hand tool kits and any other product where
there are multiple items or components that make up the unit. Please contact
the phone number below in order to obtain the replacement components
covered under warranty.
•Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user
and may not be transferred to subsequent owners.
•This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do
not allow the exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you. All claims must be sent to:
Astro Pneumatic Tool Company
372 Old US Highway 52 South
Mt. Airy, NC 27030
1 YEAR LIMITED WARRANTY
UNIVERSAL WELDING CART
UNIVERSAL WELDING CART
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
1
2
3
4
5
8
10
11
12
12
13
13
14
14
15
11 15
6 9
7
7
Call 1.800.221.9705 for questions concerning performance of the product
or other inquiries.
Page 3
8202
372 Old US Highway 52 South
Mount Airy, NC 27030
UNIVERSAL WELDING CART
8202-01
8202-02
8202-03
8202-04
8202-05
8202-06
8202-07
8202-08
8202-09
8202-10
8202-11
8202-12
8202-13
8202-14
8202-15 Shelf A
Shelf B
Shelf C
Shelf D
Support Bar A
Support Bar B
Hook
Nut, Bolt and Washer Set
Chain
Axle
Washer
Pin
Solid Wheel
Swivel Caster
Plastic Cap 1
1
1
1
1
1
2
40
2
1
2
2
2
2
2
Page 2
8202
UNIVERSAL WELDING CART
inside
outside
WARNING
• This cart is design to carry one Mig Welder and one gas cylinder only.
Always use caution when working with welding bottles. Store the cylinder
in an upright position and make sure the retaining chains are securing
the welding cylinder tightly at all times.
• Never weld on the welding cylinder.
• The cart is designed to roll on level surfaces only to use otherwise is
inviting the cart to be unstable and maybe tipping over and resulting in
injury and possible death.
• When moving the welding cart steer with the top shelf and take extra
precautions as the cart may be top-heavy and subject to tipping over.
• Never try to move the cart by pulling on any welding cables or welding
gun as this could cause the cart to tip over and possible result
in injury or death.
• Do not allow ground cable connection to come in contact with any part
of the welding cart or cylinder as this will complete a circuit which could
result in electrical arching.
• Failure to adhere to the above precautions could result
in serious injury or death.
You will only need a 10mm wrench, 10mm socket, ratchet and pliers.
REAR WHEELS
1. Slide axel thru the hollow tube located on the bottom
side of the Shelf C (8202-03)
2. Place one flat washer on each end of the axel.
3. Place the wheels on the axel.
4. Install the cotter pins in each axel hole and bend over.
5. Seat the red caps over each axel end.
FRONT WHEELS
1. Align the castor wheel bracket with four holes locate on
the bottom left side of the Shelf C (8202-03).
2. From the topside of the lower shelf install four bolts with flat
washers through the shelf (8202-03) and castor plate
(8202-14). Then, install four washers and nuts on the bolts and
tighten them with the 10MM wrench and socket combination.
3. Repeat steps 1 and 2 for the right side of the carts lower
shelf and castor.
SHELF D
1. Align the bottom holes in the sides of the Shelf D (8202-04)
with the holes in the sides of the Shelf C.
Note: the lips of the vertical support should be pointing towards the
front of the cart.
2. From the topside of the Shelf C, install a bolt with a flat
washer through the center hole of Shelf D and the
Shelf C, install a lock washer and nut on the other side
and tighten securely. If you have trouble starting the nut and
washer you can lay the cart over on its side.
3. From outside of Shelf C, you can install a bolt with a flat
washer through Shelf C and the Shelf D, (one for each
side) than install lock washers and nuts onto each bolt.
Note: Tighten these two nuts and bolts until just snug as you will
tighten them completely when the cart is fully assembled.
At this point only lightly tighten all nuts and bolts as you complete
the assembly. The last part of the assembly will involve placing
the cart on a level surface and sequentially tightening all of the
remaining nuts and bolts to achieve a welding cart assembly that
is as near level as possible.
SUPPORT BARS
1. Line up the Support Bar A rail holes with the holes located on
the left side of the Shelf C. Support Bar A only has two holes
drilled through it while the top of the rail has five holes drilled
through it.
2. From the outside of Support Bar A install a bolt with a flat
washer through each hole than install a lock washer and nut on
each bolt and tighten only lightly at this time.
3. Repeat the same steps for the Support Bar B.
CENTER SHELF
1. Line up the four front holes, two holes a pair located on each
side of Support Bar A and B.
Note: The center shelf has four lipped sides. The lips should be facing
upwards when installed correctly.
2. From the outside of the Support Bars, install a bolt with flat
washer through each hole.
3. Line up the holes on either side in the rear lip of the center shelf
with the center holes located on either side of the Shelf D. Install
a lock washer and nut on each bolt and tighten lightly at this time
TOP SHELF
1. Line up the four front holes, two located on each side of Shelf A
with the four holes, two located on each side of the support bars.
The top shelf also has three lips they should be pointed up at
time of installation. The opening of the shelf should be facing the
left side of the welding cart.
2. From the outside of the support bars, insert a bolt with a flat
washer through each hole add a lock washer and nut and tighten
lightly at this time.
3. Line up the two rear holes one located on each side of the Shelf
A with the upper holes, one located on each side of Shelf D.
4. From the outside of the Shelf D, install a bolt with a flat washer
through each hole and install a lock washer and nut on the other
side tighten very lightly at this time.
5. Line up the rear lip of the Shelf A with the top with the center
hole of Shelf D
6. On the outside of the Shelf D, insert a bolt with a flat washer
through the hole then slide one lock washer and thread one nut
and tighten lightly.
CABLE BRACKETS
1. Line up Hook (8202-07) with the 2 lower vertical holes on the
support bars located just below the top shelf. Slide one flat
washer and bolt into each of the two holes of the bracket and
through the support bars on each side of the welding cart and
tighten all four bolts securely.
Note: At this time, place the cart on a level surface and tighten all nuts
and bolts starting at center shelf. Work from support bars around the cart
and up and down until all fasteners are firmly tightened. Now your cart
will be as level as possible.