Atec HP-Agilent-66309D - Manual

143
A
Specifications
Specifications
Table A-1 lists the specifications of the dc source. Unless otherwise noted, specifications are warranted
over the ambient temperature range of 0 to 55
°
C. Specifications apply with typical cellular phone
capacitive loads from 0
µ
F to 12,000
µ
F. Sensing is at the rear terminals of the power supply after a 30-
minute warm-up period. Sense terminals are externally jumpered to their respective output terminals.
Table A-1. Performance Specifications
Parameter Agilent 66111A Agilent 66311B/D;
Agilent 66309B/D
output 1 only
Agilent
66309B/D
output 2 only
Output Ratings Voltage:
Current:
Peak Current:
0 – 15 V
0 – 3 A
5 A 1
0 – 12 V
0 – 1.5 A
2.5 A 2
Programming Accuracy
(@ 25
°
C
±
5
°
C)
Voltage:
+Current:
0.05% + 10 mV
0.05% + 1.33 mA 3
0.2% + 40 mV
0.2% + 4.5
mA
DC Measurement Accuracy
(via GPIB or front panel meters with
respect to actual output @ 25
°
C
±
5
°
C)
Voltage:
Current:
High Current range 4
+20 mA to + rated I:
−
20 mA to
−
rated I:
Low Current range
−
20 mA to +20 mA:
0.03% + 5 mV
see below
0.2% + 9 mA
0.2% + 9 mA
NA
0.03% + 5 mV
see below
0.2% + 0.5 mA
5
0.2% + 1.1 mA
0.1% + 2.5
µ
A
6
0.2% + 15 mV
0.2% + 3 mA
NA
NA
NA
Ripple and Noise
(in the range of 20 Hz to 20 MHz
with outputs ungrounded or with
either terminal grounded) Voltage (rms/p-p):
Current (rms):
1 mV/6 mV
7
2 mA
1 mV/6 mV
7
2 mA
Load Regulation
(change in output voltage or current
for any load change within ratings) Voltage:
Current:
2 mV
0.75 mA
1.6 mV
0.375 mA
Line Regulation
(change in output voltage or current
for any line change within ratings) Voltage:
Current:
0.5 mV
0.75 mA
0.4 mV
0.25 mA
Transient Response Time
(for the output voltage to recover to
20 mV below its final setting) < 35
µ
s
8
< 400
µ
s
9
1 Peak current for up to a 7 millisecond time period. Average current cannot exceed 3 A.
2 Peak current for up to a 1 millisecond time period. Average current cannot exceed 1.5 A.
3 0.05% +2.3mA when programming between zero and 0.03% of full scale current.
4 Agilent 66111A units do not have a low current range, the dc measurement accuracy applies from 0 amperes to the rated current.
5 Applies with current detector set to DC. ACDC mode accuracy is 0.2% + 3mA for sourcing and 0.2% + 3.6 mA for sinking.
6 This specification may degrade slightly when the unit is subjected to an RF field
≥
3 V/meter.
7 Specification is for phone capacitance greater than 6
µ
F.
8 Applies to the negative portion of the output voltage transient waveform, following a 0.1 A to 1.5 A load current change.
(Applies with unit set to High capacitance compensation range with 5
µ
F minimum output load capacitance.)
9 Following a 0.75 A to 1.5 A load change.