Baldwin Bethpage Sectional Trim - Manual

Installation Instructions
E N G L I S H
Congratulations!
With your purchase of this Premium Full Dummy Trim Set, you’re among
a group of discerning individuals who know the intrinsic value of
selecting the finest—Baldwin.
Our step-by-step installation instructions will help guide you through your
project quickly and easily.
Before you begin your installation, read and understand the installation
instructions and marking templates. If you have any questions, please
do not hesitate to contact our Baldwin Consumer Help Line at,
1-800-566-1986. We’re here to help! We thank you for your purchase
and wish you the fullest enjoyment of your Baldwin product.
Care and Maintenance
WARNING: Do not attempt to clean your hardware with any type of
abrasive cleaners, solvents, or chemicals. These types of cleaning agents
may mar the finish. A damp cloth is all that is necessary to wipe clean.
Note: Finish Number 102, Oil-Rubbed Bronze, can be cleaned with light
machine oil and wiped with a dry cloth.
Consumer Help Line
1-800-566-1986
Hours: 8 a.m. to 8 p.m. E.S.T. – Monday - Friday
10 a.m. to 6 p.m. E.S. T. – Saturday
If you have trouble installing your Baldwin product, feel free to call our
toll-free Consumer Help Line.
Premium Entrance Set
FULL DUMMY
SECTIONAL TRIMS
PK.5711
Full Dummy Installation 3
3
If Full Dummy Trim will be
installed next to an active
door, height from bottom of
door and backset must match
the active door. Backset is the
distance from the edge of door
to center of hole (A), the 2
1 ⁄
8
"
dia. hole. Otherwise, locate
center hole (A) 38" from floor.
Tape template to door.
4
Locate and mark positions
for (A, B, and C) on template.
5
Very carefully drill (A) 2 1 ⁄
8
"
hole into one side of door face
until drill bit starts to protrude
on opposite side.
Important: Drill
perpendicularly (at a 90º
angle) to door.
6
Complete drilling hole (A)
from opposite side of door.
Drill (B)
1 ⁄
2
" hole into door
exactly at pencil mark.
7
Very carefully drill (C) 5 ⁄
16
"
hole into door exactly at
pencil mark.
1
Measure the diameter of
top hole (B) in door. If hole is
2
1 ⁄
8
", orient the locating plate
as shown in fig. 1. If hole is
less than 2
1 ⁄
8
", orient locating
plate as shown in fig. 2.
2
Insert dummy cylinder
through dummy cylinder
collar and into outside of door.
From inside, insert retaining
screw through lock washer
and locating plate, then screw
into dummy cylinder.
4
Attach outside handleset by
inserting the #10-32 x 2 3 ⁄
4
" oval
head screw on inside of door
through rectangular screw base
and the lower hole (C). Leave
screw loose for adjustment.
Note: Go to door preparation
if you do not have a lower
hole (C).
3
Place the dummy interior
top plate over locating plate
and fasten in place using the
#8-32 x
5 ⁄
8
" machine screw
though hole in center of trim.
7
Slide knob/lever onto dummy
inside adapter with set screw
hole down and toward hinges
until it is flush with rosette.
Insert set screw and tighten with
Allen wrench.
1
Pull door toward you to
check if it’s level. Observe
contact of door to jam and
make sure it’s level. Adjust if
necessary.
Door Preparation (If Needed) 2
Before You Begin 1
• Remove and discard all materials and screw(s) used for packing your
Full Dummy Trim Set. Verify that you have all parts pictured on
exploded view section of instructions.
• Check the thickness of the door. This Full Dummy Trim Set works on
doors 1 3 ⁄
4
" thick only. For doors greater than 1 3 ⁄
4
" up to 2 1 ⁄
4
" thick,
contact our Consumer Help Line at 1-800-566-1986. The conversion
kit part number for this item is 5399.XXX.D; please specify the finish of
your product.
• Follow the step-by-step sequence to ensure proper
operation of your Baldwin lockset.
• If your door is pre-drilled, see Full Dummy installation step 1. If it is not
pre-drilled, see door preparation step 1.
• We recommend spreading cardboard over floor to prevent scratching parts
and marring floor.
• Always wear protective eyewear.
Note: The illustrations in these instructions depict the outside handle
being installed on the right of the door. For installation of the outside
handle on the left of the door, proceed as if all illustrations were reversed.
PK.5711
12/11
Exploded View
Outside Handleset
Trim
Rectangular Screw Base
#10-32 x 2 3 ⁄
4
" Oval Head Screw
Dummy Cylinder
Dummy Cylinder Collar
#8-32 x 5 ⁄
8
" Machine Screw
#10-32 x 1 1 ⁄
4
"
Truss Head
Screws
Locating Plate
Set Screw
Lock Washer
Dummy Interior Top Plate
2" Retainer Screw
Dummy Inside
Adapter
Allen Wrench
hole template
low side of bevel
door stop
A
B= 1 ⁄
2
"
A
C
top of door
2
(Aerial View) To ensure
proper alignment, only use
hole template on side facing
doorstop.
Helpful Hint: Some doors
have a beveled edge with bevel
facing doorstop.
inside
5
Place the dummy inside
adapter on the door, aligning the
holes in adapter with post on
outside handleset. Secure with
two #10-32 X 1
1 ⁄
4
" truss head
screws.
inside
6
Place rosette over dummy
inside adapter. Using rose
retainer wrench, thread the rose
retainer onto the threaded
portion of the adapter.
inside inside
Rosette
Knob
Handleset Installation
Fasteners
Protective
Eyewear
Phillips
Screwdriver
Tape
Measure
Flat Head
Screwdriver
2 1 ⁄
8
" Dia. Face
Bore Hole Saw
Electric
Drill
1 ⁄
2
" Wood
Chisel
1 ⁄
8
" Wood
Drill Bit
5 ⁄
16
" Wood
Drill Bit
1 ⁄
2
" Wood
Drill Bit
Pencil Chalk,
Grease Pencil, or
Lipstick
Utility
Knife
Masking Tape 24" Level Hammer
Helpful Tools
Wood Filler Beeswax
or Soap
Required Tools
2" Retainer
Screw
(2) #10-32 x 1 1 ⁄
4
"
Truss Head Screws
#8-32 x 5 ⁄
8
"
Machine Screw
#10-32 x 2 3 ⁄
4
"
Oval Head Screw
Set Screw
inside inside
fig. 1
fig. 2
B
B
C
Post
Rose Retainer
Right-Hand Lever
Left-Hand Lever
Rose Retainer Wrench
1" Spade Bit or
1" Hole Saw
(Recommended)
4
1
If weather stripping is
not installed, you must
install weather stripping
prior to strikeplate
installation.Mark center of
deadbolt with chalk, grease
pencil, or lipstick. Shut door
and lock deadbolt to mark
center point on inactive door.
3
On inactive door, align
strike hole template with center
point. Mark holes for center of
latch bolt and outer corners of
both strikes with pencil.
4
For Deadbolt and
Latch Strikeplates: Mark
drill points
5 ⁄
16
" above and
below center points. Bore two
1" holes 1
1 ⁄
4
" deep for deadbolt
dustbox and two 1" holes 1"
deep for latch dustbox. Score
chisel guide into door frame
with utility knife.
5
For Deadbolt and Latch
Strikeplates: Chisel out holes
for dustboxes. Chisel out cavity
so deadbolt strikeplate and latch
strikeplate fit flush with
doorframe. For deadbolt
strikeplate, cavity is
7 ⁄
32
" deep.
For latch strikeplate, cavity is
3 ⁄
32
" deep.
6
For Deadbolt
Strikeplate: Using reinforcing
strikeplate as a template, drill
four
1 ⁄
8
" pilot holes for #8 x 3 ⁄
4
"
combination screws.
9
For Latch Strikeplate:
Using latch strikeplate as a
template, drill two
1 ⁄
8
" pilot holes
for the #8 x 3 ⁄
4
" screws.
7
For Deadbolt Strikeplate:
Insert dustbox into hole, add
reinforcing strike, and secure with
four #8 x
3 ⁄
4
" combination screws.
Two screws are supplied with active
trim and two are supplied with
dummy trim.
Important: Do not install
3” screws in double door
applications.
Helpful Hint: When installing
wood screws it is recommended to
put beeswax or soap on screw
threads to improve installation.
8
For Deadbolt
Strikeplate: Add strikeplate
and secure with #8-32 x
1 ⁄
4
"
screws.
inside inside inside
10
For Latch Strikeplate:
Insert dustbox into hole, add
strikeplate, and secure by
inserting #8 x
3 ⁄
4
" wood screws
into pilot holes.
inside inside inside inside
Troubleshooting Guide
If parts are missing do not return product. Please call Baldwin's Consumer Help Line at 1-800-566-1986 and we will quickly
send the parts to you.
Problem
Screws are all tight but the hardware is not firmly attached to the door.
Knob or lever keeps coming off the spindle.
Solution
Check door thickness. Door must be 1
3 ⁄
4
" thick. Hardware will not
install on doors less than 1 3 ⁄
4
" thick.
Ensure that set screw on knob or lever is fully tightened on the spindle
with Allen wrench provided. Refer to full dummy installation step 7.
inside
For Double Door Installation Only
Strikeplate Installation for Inactive Door (Strikeplate Hardware is Shipped with Active Trim)
IMPORTANT! You must install Baldwin strikeplate or your warranty is void.
2
(Arial View) Alignment
of Latch Strikeplate:
Curved edge of latch strikeplate
should face curved side of
latchbolt.
inside
Door Frame Template
Door Hole Template
(2) #8 x 3 ⁄
4
"
Combination
Screws
Strikeplate
Installation
Fasteners
for Double
Door
Installation
Only
www.baldwinhardware.com
©2011 Baldwin Hardware Corporation
841 East Wyomissing Blvd., Reading, PA 19611
Remember Baldwin
With the completion of your project, remember that Baldwin quality
hardware products are available for all your decorating and remodeling
needs. Matching entrance sets for exterior doors, beautiful bath
accessories, and a complete selection of cabinet and door-enhancing
hardware are all available from your Baldwin retailer.
To request a product brochure or the name of a retailer near you,
call 1-800-566-1986.
Baldwin offers a vast array of exceptional solid brass products to elegantly
enhance all areas of the home. Each collection features a wide variety of
beautiful, high-fashion finishes. From door hardware to bath accessories,
Baldwin provides the discriminating decorator with numerous options to accent
and complement the home’s ambience with distinction, taste, and fine detail.
Browse through the Baldwin Collection of beautiful locks, bath
accessories and decorative hardware. Compare styles and finishes.
There are thousands of photos and descriptions available to help you
coordinate hardware throughout your home. Create your ideal "wish
list" then visit your Baldwin Retailer or Dealer. Visit
www.baldwinhardware.com today!
Tahoe ®
5325 5320 5315 5305
Madison ® Logan ™ Canterbury ®
PK 5711-ENG_02BALD109 Tahoe FD v5 7/27/11 11:54 PM Page 1