Baldwin Soho AC Z-Wave Deadbolt User Manual

Db b b, Français, Bd c

Advertising
background image

FOR PRODUCT WITH A HOME AREA NETWORK

(HAN) GATEWAY SYSTEM CONNECTION.

1. Please make sure you have followed all the steps in the

lock Installation and Programming Manual.

4. User Code Information:

Code or codes that are programmed before the installation of the daughter

card will be disabled.

Code or codes that are programmed after the installation of the daughter

card will remain valid.

Once the lock has been included into the (HAN) system, you can program up

to 30 codes.

We suggest you add and change codes from the system controller.

Deleting a code can only be done from the system controller.

3. For inclusion or exclusion of the lock, refer to the Home Area Network (HAN)

system instructions and note functions referred to in Figure 2

and the chart below.

2. Make sure the RF daughter card is properly installed,

seated and connected, see Figure 1, callout .

Light (under the reference card)

will illuminate

Yellow for 5 seconds

during the Inclusion process and will

illuminate

Red for 5 seconds during

the Exclusion process.

POUR UN PRODUIT COMPRENANT

UNE CONNEXION À UN SYSTÈME DE

COMMUNICATION INTER-RÉSEAU

DOMESTIQUE.

1. Veuillez vous assurer de suivre toutes les étapes dans le Guide de

programmation et d'installation du serrure.

3. Pour inclure ou exclure le serrure, veuillez consulter les instructions

du système de réseau domestique et prenez note des fonctions

dont on fait référence à la Figure 2 et le tableau dessous.

2. Veuillez vous assurer que la carte fille RF est correctement installée,

bien fixée et connectée, consultez la Figure 1, point .

La lumière (sous la carte

de référence) s'allumera en

Jaune pendant 5 secondes

au cours du processus

d'inclusion et elle s'allumera

en

Rouge pendant 5

secondes au cours du

processus d'exclusion.

4. Information sur le code d'utilisateur:

● Le code ou les codes qui sont programmés

avant l'installation de la

carte fille seront désactivés.

● Le code ou les codes qui sont programmés

après l'installation de la

carte fille resteront activés.

● Une fois le serrure inclus dans le système inter-réseau domestique,

vous pouvez programmer jusqu'à 30 codes.

● Nous vous suggérons d'ajouter et de changer les codes du contrôleur

de système.

● La suppression d'un code ne peut être effectuée qu'à partir du

contrôleur de système.

CONFORMITÉ RÈGLEMENTAIRE

Ce produit est conforme aux normes établies par les organismes de

règlementation suivants :

Federal Communications Commission (FCC, États-Unis)

Industrie Canada

Fig. 2

C

C

A

A

A

Fig. 1

RF

Protocol

Zigbee

Z-Wave

Inclusion

Process

D

B

B

B

Button used in

Exclusion

Process

Button used in

Protocole

RF

Zigbee

Z-Wave

Processus

De Inclusion

D

B

B

B

Bouton utilisé

pour le

Bouton utilisé

pour le

Processus

De Exclusion

REGULATORY COMPLIANCE

This product complies with standards established by the following regulatory bodies:

Federal Communications Commission (FCC)

Industry Canada

FCC

FCC ID: NUL5024093ZGB (Wireless Lock Module 5024093)

FCC ID: NUL5024095ZWV (Wireless Lock Module 5024095)

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: ( 1 ) this device may not cause harmful interference, and

( 2 ) this device must accept any interference received, including interference that

may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communi-cations. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT!

Changes or modifications not expressly approved by the manufacturer

could void the user’s authority to operate the equipment.

INDUSTRY CANADA

This Class B digital apparatus complies with Canada ICES-003. CAN/CSA-C22.2 NO.

14-05 (Industrial Control Equipment) Operation is subject to the following two conditions: (

1 ) this device may not cause interference, and ( 2 ) this device must accept any interfer-

ence, including

interference that may cause undesired operation of the device.

Canadian ID IC: 3022A-5024093ZGB

Canadian ID IC: 3022A-5024095ZWV

Z-WAVE

• Security enabled Z-Wave product

• Security enabled Z-Wave controller must be used in order to fully utilize product.
This Z-Wave-enabled door lock can be included, operated, and is fully interoperable with

any Z-Wave secure controller.

ENGLISH

INSTRUCTIONS

D'INSTALLATION

FRANÇAIS

INSTALLATION

INSTRUCTIONS

Press program button below once to enter

the 1st code & twice for the 2nd code
Enter code on exterior keypad

Press on exterior keypad to set code

READY

PROGRAM

BUTTON

B

D

C

RF Card

44571-03

1 / 2

Db: ai

EO104365-25

Copyright © 2010 Black & Decker Corporation

Advertising
This manual is related to the following products:
Table of contents