J&M JD-STS series - Manual

Combine Grain Tank Set-Up Instructions
for John Deere STS Series Combines Lanyards and
Lynch Pins
shown below
are typical on
Front, Rear
and Side
Panels
Fold this Panel First
Remove Knock-outs to
install Sensor Mounting
Bracket. When installing
Tip-Up Panels, DO NOT
remove knock-outs.
Sensor Mounting Bracket
will be installed on Tip-Up
Panel.
Remove Knock-outs and locate GPS Bracket here.
Remove Knock-out and relocate existing light here.
Assembly Instructions
For STS Models 9560, 9660 or 9760 Series Combines with 16”
auger, install additional tank brace before Step 1 (see insert).
Step 1:
Attach both rear braces to combine hopper using (8) 3/8” x 1” Flange
Bolts and (8) 3/8” Flange Nuts.
Position the rear brace on top of the rear C-Channels of the combine
and drill 3/8” holes in the combine hopper to attach these braces.
NOTE: C-Channels are located under door hatch close to grain tank
(door hatch may need to be slid back to install braces)
Step 2:
Place frame halves on combine hopper. Loosely fasten frame halves
to existing brackets of combine hopper using (4) 5/16” x 1 1/2” Bolts,
(8) 3/8” Heavy Washers and (4) 5/16” Flange Nuts. To prevent grain
leakage, slide the Frame Shim between the frame and the tank to
ensure a tight seal. For STS Models with 18” auger, place the four
Clamp Plates below the hinges of the frame. Loosely secure the frame
(and frame shim) either to the hinge or the adjacent tank bracket using
5/16” x 5/8” Flange Bolts and Flange Nuts. Do not tighten Clamp
Plates to hinge as they may need repositioned to ensure a proper fit.
# Part # Description Qty
1 STS-CP Corner Panel 4
2 STS-FRSP Front/Rear/Side Panel 4
3 STS-FRF Front/Rear/Frame 2
4 STS-TRL Tubing Rail (Left with cut-out) 1
4 STS-TRR Tubing Rail (Right) 1
5 STS-RB Rear Brace 2
6 JD-SMB Sensor Mounting Bracket 1
7 CTE-PP Plastic Plug 8
8 CTE-PL Plastic Lanyard 24
9 CTE-LP Lynch Pin 24
10 JD-EW Extension Wire 1
11 FB-516112 5/16" x 1 1/2" Flange Bolt 4
12 HB-384 3/8" x 4" Bolt 8
13 HB-38412 3/8" x 4 1/2" Bolt 8
14 6MM-475 6MM x 4 3/4" (8.8) 8
15 FB-381 3/8" x 1" Flange Bolt 10
16 FB-51658 5/16" x 5/8" Flange Bolt 26
17 FN-516 5/16" Flange Nut 30
18 LN-38 3/8" Lock Nut 8
19 6MM-NLN 6MM Nylon Lock Nut 8
20 HW-38 3/8" Heavy Washer 8
21 CTE-HRW Hand Rail Weldment 1
22 DS-14112 1/4" x 1 1/2" Drill Screw 1
23 IW-71212 Inspection Window 4
24 62095-7 Window Molding 4
25 FN-38 3/8" Flange Nut 20
26 GPS-RB1 GPS Bracket 1
27 GPS-RB2 GPS Bracket Adapter 1
28 STS-TB1 Tank Brace Support 1
29 CTE-SS1 Step 1
30 STS-CP18 Clamp Plate (combines w/18" auger) 4
31 STS-FS1 Frame Shim 2
NOTE: The Rear Braces are not
needed for 2006 and newer 9660,
9760 or 9860 STS Model combines.