Chapin 7207947 User Manual

Warning, Parts, piezas, pièces, Hose to tank 2. nozzle / extension wand

Advertising
background image

Hazard: Improper use or failure to follow instructions can result in explosive failure causing serious eye or other

injury.

For safe use of this product you must read and follow all instructions. Do not leave a pressurized sprayer in the hot

sun. Heat can cause pressure build-up. Do not store or le

ave solution in tank after use. Always wear goggles, gloves, long

sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove pump if there is pressure

in sprayer. Never stand with face or body over

top of tank when pumping or loosening pump to prevent ejecting pump

assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than the original

pump. Do not attempt to modify or repair this product except with original manufacturer’s parts. Never spray flammable

materials or heat, pressure, or gas producing chemicals. Always read and follow manufacturer’s instructions before

use with this sprayer as some chemicals may be hazardous when used with this sprayer.

WARNING!

Sk-1113-1

Parts, Piezas, Pièces

6-2001

Hose Kit: 2 nuts,2 barbs, hose

Juego de manguera: 2 tuercas, 2 lengüetas, manguera

Nécessaire de tuyau: Deux écrous, deux ardillons, tuyau

6-2000

Shut-off Handle

Mango de cierre

Poignée du robinet

301120-4

Brass FanNozzle

Tobera en latón

Buse-éventail en laiton

Printed in USA

1. Hose to Tank

2. Nozzle / Extension Wand

Attach nozzle to shut-off handle or extension wand.

3. Filter

The filter helps prevent clogging while spraying. It is located on the end of the outlet tube inside your

sprayer tank.To clean filter, remove the discharge assembly from the tank (Fig.1A). Make sure the

filter is positioned at the bottom of the tank as pictured

Note:

Filters are not supplied with deck sprayers.

1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace hose before using. Replace

with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for signs of deterioration of

body and bottom. Any sign of deterioration indicates possible tank weakening and could result in explosive bursting under pressure. If any

of these signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.

4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.

5) Do: Pump plunger 8-10 strokes and inspect for leaks.

6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.

7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with Filling, Pressurizing and

Spraying Instructions.

6. Pre-Use Check

7. Filling

1) Do: Turn pump handle counterclockwise and remove pump

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.

8. Pressurizing and Spraying

Do:

Turn handle clockwise to tight-

en. Push handle down, turn 1/4

turn counterclockwise to release.

Do:

Pump until you

feel resistance.

Do:

Push handle, down, turn 1/4 turn clockwise to

lock. Begin spraying. Re-pump sprayer as required

to maintain spray force.

10. Care, Storage and Maintenance

1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and Spraying Instructions,

except pump unit only 8-10 strokes.

2) Do: Open shut-off and allow water to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.

6-5385

Spray Shield

Pantalla de pulverización

Bouclier de pulvérisation

6-5364

Measure Cup

Taza para medir

Tasse à mesurer

3-7749-18

Extension wand, Vara de extensión, Lance de rallonge

WARNING:

Handling the brass parts of this product will expose you to lead, a chemical known to the State of California

to cause birth defects and other reproductive harm. Wash hands after handling.

Congratulations!

You have just purchased a quality Chapin product.

Register Your Sprayer Online @ www.chapinmfg.com

Questions?

Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!

Usted acaba de adquirir un producto de calidad Chapin.

Registre su pulverizador en línea en www.chapinmfg.com

¿Preguntas?

No regrese a la tienda;

llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!

Vous avez acheté un produit de qualité Chapin.

Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:

www.chapinmfg.com

Questions ?

Ne retournez pas au magasin.

Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com

010879-1 (A) R0110

8A

Note:

Your particular sprayer may not include all parts pictured above.

Nota:

Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque :

Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

Discharge/ Assembly

• Insure the tool holder is assembled to the tank adapter before mounting the discharge assembly (Fig.1A). The Tool

Holder snaps into the groove of the tank adapter. Figure 1D shows how the shield and cup are mounted.

• Insert the outlet tube portion of the discharge assembly into the tank adapter (Fig. 1A).

• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap between the tank adapter and outlet tube adapter.

• Firmly tighten the retaining nut to the tank adapter (Fig. 1C).

WARNING!

To prevent hose from blowing off, hose must cover both barbs on the outlet tube adapter and

touch flange (Fig. 1B) before hose nut is securely tightened (Fig. 1C).

301272-4

Adjustable Brass Nozzle

Boquilla de latòn regulable

Buse en laiton réglable

6-4566

4 Position Nozzle

Boquilla de 4 posiciones

Buse à 4 positions

3-2102

Poly Fan Nozzle Kit

Juego de boquilla en abanico polietileno.

Nécessaire de buse éventail en polyéthylène

1A

301481

Pump Assembly

Ensamblaje De La Bomba

Assemblage De La Pompe

6-5386

Repair Kit

Juego de reparación

Kit de réparation

010842

Tool Holder

Soporte para la herramienta

Porte-outils

1C

Retaining Nut -

Securely tightened.

Tool

Holder

Measuring

Cup

Spray

Shield

1D

1B

No

Gap

Tank

Adapter

Outlet

Tube

Adapter

Tool

Holder

Outlet

Tube

Discharge

Assembly

2A

Nozzle

Shut-off

2B

Extension Wand

4. Fatigue-free Spraying

Filter

3A

8B

8C

For constant spraying, push down on shut-off handle and move gray locking mechanism away

from you. To release, squeeze handle and move the gray locking mechanism back toward you.

Note: Fatigue-free spraying lock is not supplied with all sprayers.

5. Shield Attachment to Wand

Snap shield onto

wand as shown.

Using the spray shield will

help protect your plants from

over spray.

5A

5B

4A

2D

2C

Red,

Fine spray for

finer washes

Blue,

Medium spray for

sealers

Yellow,

Course spray for semi-

transparent stains

Attach cap to shut-off handle or extension wand (Fig. 2D-2E).

Deck Sprayers Only ( Fig. 2C-2E)

Insert nozzle into cap (2C).

2E

Pull handle straight up.

Insert notches from

underside of handle

into plunger grooves

and turn counter-

clockwise.

Remove plunger and diaphragm.

Clean plunger, diaphragm

and body. Flip diaphragm and

replace.

Tighten plunger clockwise until

flush to top of shut-off body.

Do not over-tighten or unit

may not spray. Slide forks un-

der plunger, push handle down

until it snaps into place.

11. Troubleshooting

-

Tank pressurizes but does not spray.

11A

11B

11C

Handle

Plunger

Body

Diaphragm

11D

Plunger flush

with body

WARNING:

Release pressure in tank before troubleshooting.

Clean Nozzle Assembly (Fig. 11E) -Remove nozzle cap. Clean and re-assemble.

Clean shut-off (Fig. 11A- 11D)

11E

Nozzle Cap

9. To Release Pressure

1) Your sprayer is equipped with a pressure release button. To release

pressure press red button until air is completely exhausted.

2) Do: Point air flow away from you and others until air has escaped.

9A

Advertising