Chapin 1480 - Manual

Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store or
le ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot
protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never
stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means
other than the original pump. Do not attempt to modify or repair this product except with original
manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas producing chemi-
cals. Always read and follow manufacturer’s instructions before use with this sprayer as some
chemicals may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-1925
Printed in USA
1. Hose to Tank
2. Nozzle
Make sure hose is pushed all the
way to the tank. Make sure hose
clamp is tight and below the
hose barb. Turn clockwise with a
screwdriver to tighten.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of
tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 10-20 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed
with Filling, Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
5. Pressurizing and Spraying
WARNING: Handling the brass parts of this product will expose you
to lead, a chemical known to the State of California to cause birth
defects and other reproductive harm. Wash hands after handling.
2-1100-23 (A) R0209
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing and
Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in
cover.
7. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
Hose Barb
Pump until you
feel resistance.
Turn handle clock-
wise to tighten.Push
handle down, turn
1/4 turn counter-
clockwise to release.
Push handle, down, turn 1/4
turn clockwise to lock. Begin
spraying.Re-pump sprayer as
required to maintain spray
force.
Attach nozzle to shut-off handle or extension wand.
1A
2A 2B
5A 5B 5C
Parts, Piezas, Pièces
6-6136
Hose
Manguera
Tuyau
6-1866
Shut-off Handle
Mango de cierre
Poignée du robinet
6-6000
Nozzle
Tobera
Buse
6-3337
Strap
Correa
Sangle
6-7711
Extension wand, Vara de extensión, Rallonge
3-4843
Fan Nozzle Pack
Paquete de boquilla a chorro
Ensamble de buse à jet éventail
Red,
Fine spray for
finer washes
Blue,
Medium
spray for
sealers
Yellow,
Course spray
for semi- trans-
parent stains
For constant spraying, push down on shut-off handle
and move locking mechanism away from you. To re-
lease, squeeze handle and move the locking mechanism
back towards you.
6. Fatigue-Free Spraying
Fan spray Stream spray
2C 2D
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡
Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
Insert Filter. Insert O-ring.
Insert appropriate nozzle
into cap.
Attach cap with nozzle to end
of housing.
Cap
Nozzle Filter
Housing
O-ring
Shut-off
or Wand
6A
2E 2F
2G 2H