Chapin 1941 - Manual

Make sure hose is pushed all
the way to the tank. Make
sure hose clamp is tight and
below the hose barb. Turn
clockwise with a screwdriver
to tighten. .
Hose Barb
Hazard: Improper use or failure to follow instructions can result in explosive failure
causing serious eye or other injury. For safe use of this product you must read and follow all
instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-
up. Do not store or le ave solution in tank after use. Always wear goggles, gloves, long sleeve
shirt, long pants and full foot protection when spraying. Never use any tool to remove pump
if there is pressure in sprayer. Never stand with face or body over top of tank when pump-
ing or loosening pump to prevent ejecting pump assembly and/or solution from striking and
injuring you. Never pressurize sprayer by any means other than the original pump. Do not
attempt to modify or repair this product except with original manufacturer’s parts. Never
spray flammable materials or heat, pressure, or gas producing chemicals. Always read
and follow manufacturer’s instructions before use with this sprayer as some chemicals
may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4627
Printed in U.S.A.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions
are found, replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior
and exterior of tank for signs of deterioration of body and bottom. Any sign of deteriora
tion indicates possible tank weakening and could result in explosive bursting under pres
sure. If any of these signs are found, discard tank immediately and replace. Do not attempt
to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty
tank, and proceed with Filling, Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to
accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in
tank and tighten securely.
7. To Release Pressure
1 Do: With pump facing away, turn locked handle counterclockwise until air begins
to escape. Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling,
Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and
empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod
through opening in cover.
WARNING: Handling the brass parts of this product will
expose you to lead, a chemical known to the State of California
to cause birth defects and other reproductive harm. Wash
hands after handling.
2-1101-10 (A) R0209
1. Hose to Tank
2. Nozzle
6-3337
Strap
Correa
Sangle
Parts, Piezas, Pièces
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
6-1866
Shut-off Handle
Mango de cierre
Poignée du robinet
6-6000
Nozzle
Tobera
Buse
Attach nozzle to shut-off handle or extension wand.
TO LOCK HANDLE: Push handle down to depress coil spring and turn handle 1/4 turn
clockwise, then allow handle to raise into lock position.
5. Pressurizing and Spraying
5A 5B
TO RELEASE HANDLE: Push down to depress coil spring
and turn handle counterclockwise 1/4 turn, then lift handle.
Pump until you feel resistance.
TO LOCK PUMP: Place pump prongs down into slots in funnel,
turn clamp clockwise to furthest position under bottom slot, then
turn handle clockwise until tightly locked and sealed in place.
TO UNLOCK PUMP: Turn handle counterclockwise until
3-prong clamp is loose. Then rotate clamp counterclockwise to
stop and lift out.
5C
5D
5. Pressurizing and Spraying, continued
For constant spraying, push down on shut-off
handle and move locking mechanism away
from you. To release, squeeze handle and move
the locking mechanism back towards you.
6. Fatigue-Free Spraying
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
5E
5F
6-7703
Extension wand, Vara de extensión, Rallonge
6-7701
Extension wand, Vara de extensión, Rallonge
6-7711
Extension wand, Vara de extensión, Rallonge
1A
6A
6-6136
Hose
Manguera
Tuyau
2A 2B