Chapin 1999 - Manual

Lock
Position
Hazard: Improper use or failure to follow instructions can result in explosive failure causing
serious eye or other injury. For safe use of this product you must read and follow all instructions.
Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure build-up. Do not store
or le ave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full
foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent eject-
ing pump assembly and/or solution from striking and injuring you. Never pressurize sprayer by any
means other than the original pump. Do not attempt to modify or repair this product except with
original manufacturer’s parts. Never spray flammable materials or heat, pressure, or gas produc-
ing chemicals. Always read and follow manufacturer’s instructions before use with this sprayer
as some chemicals may be hazardous when used with this sprayer.
WARNING!
Sk-1113-1
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-4629
Printed in U.S.A., Impreso en E.U.A, Imprimé aux U.S.A.
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,
replace hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of
tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank
weakening and could result in explosive bursting under pressure. If any of these signs are found, discard
tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and
proceed with Filling, Pressurizing and Spraying Instructions.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
8. To Release Pressure
1 Do: To release pressure in the sprayer just pull the ring on the relief
valve until all pressure is released from the sprayer.
2) Do: Stay away from the sprayer until all air has escaped.
9. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pressurizing
and Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening
in cover.
WARNING: Handling the brass parts of this product will expose you to lead, a chemical known
to the State of California to cause birth defects and other reproductive harm. Wash hands after
handling.
010325-1 (A) R0209
1. Hose to Tank
2. Nozzle
1-5797
Nozzle .5 GPM
Boquilla
Buse
Parts, Piezas, Pièces
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Attach the hose by screwing the swivel
nut clockwise and tightening to 37 in. lbs.
Refer to Pre-use check before using.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions?
Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡
Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas?
No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ?
Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
6-5373
Holster
Funda
Étui
6-6092
Hose Black
Manguera para trabajos
pesados Negro
Tuyau pour service
intense Noir
6-7703
Extension wand, Vara de extensión, Rallonge (1949)
6-6062
Shut-off Handle
Mango de cierre
Poignée du robinet
Attach nozzle to shut-off handle or extension wand.
TO LOCK HANDLE: Push handle down to
depress coil spring and turn handle 1/4 turn clock-
wise, then allow handle to raise into lock position.
5. Pressurizing and Spraying
5A 5B
TO RELEASE HANDLE: Push down to depress coil spring and turn
handle counterclockwise 1/4 turn, then lift handle.
Pump until you feel resistance.
TO LOCK PUMP: Place pump prongs
down into slots in funnel, turn clamp
clockwise to furthest position under
bottom slot, then turn handle clockwise
until tightly locked and sealed in place.
TO UNLOCK PUMP: Turn handle counterclockwise until 3-prong clamp
is loose. Then rotate clamp counterclockwise to stop and lift out.
5C
5D
5. Pressurizing and Spraying, continued
5E
5F
1A
2A 2B
SET COMPRESSOR REGULATOR AT 50 PSI
7. To Use Special Valve to Pressurize Sprayer
To pressurize sprayer by using the special valve first remove plastic
cap from the tire valve stem. Pressurize the sprayer by using a
standard air chuck connected to an air compressor as you would
inflating a tire on a car. After pressurizing the sprayer replace
plastic cap on the tire valve to avoid getting dirt in the valve.
7A
8A
For constant spraying, push down on shut-off handle
and move locking mechanism away from you. To re-
lease, squeeze handle and move the locking mechanism
back towards you.
6. Fatigue-Free Spraying
6A