Chapin 22790 - Manual

WARNING!
Printed in U.S.A.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on
chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: over fill to
accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in
tank and tighten securely.
5. Pressurizing and Spraying
Do: Turn handle clockwise to tighten.
Push handle down, turn 1/4 turn
counterclockwise to release.
Do: Pump until you
feel resistance.
Do: Push handle, down, turn 1/4 turn clockwise to
lock. Begin spraying. Re-pump sprayer as required
to maintain spray force.
7. To Release Pressure
1) Your sprayer is equipped with a pressure relief/release valve.
To release pressure lift and hold the cap until air is completely
exhausted, OR, turn the valve slowly counterclockwise until
you hear air escaping and wait air is completely exhausted.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, refill with water. Follow Filling, Pres-
surizing and Spraying Instructions, except pump unit only 8-10 strokes.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty
sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through
opening in cover.
010538-3 (A) R0909
5A
1. Hose to Tank
5B
WARNING: Handling the
brass parts of this product
will expose you to lead, a
chemical known to the State
of California to cause birth
defects and other reproduc-
tive harm. Wash hands after
handling.
2. Nozzle
1A
Hazard: Improper use or failure to follow instructions can result in explosive failure
causing serious eye or other injury. For safe use of this product you must read and follow
all instructions. Do not leave a pressurized sprayer in the hot sun. Heat can cause pressure
build-up. Do not store or le ave solution in tank after use. Always wear goggles, gloves, long
sleeve shirt, long pants and full foot protection when spraying. Never use any tool to remove
pump if there is pressure in sprayer. Never stand with face or body over top of tank when
pumping or loosening pump to prevent ejecting pump assembly and/or solution from strik-
ing and injuring you. Never pressurize sprayer by any means other than the original pump.
Do not attempt to modify or repair this product except with original manufacturer’s parts.
Never spray flammable materials or heat, pressure, or gas producing chemicals. Always
read and follow manufacturer’s instructions before use with this sprayer as some chemi-
cals may be hazardous when used with this sprayer.
Sk-1113-1
For constant spraying, push down on shut-off
handle and move locking mechanism away from
you. To release, squeeze handle and move the
locking mechanism back towards you.
6. Fatigue-Free Spraying
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Attach nozzle to extension wand (22790).
6-1898
Shut-off Handle
Mango de cierre
Poignée du robinet
Parts, Piezas, Pièces
6-6141
Hose Brown
Manguera Castaño
Tuyau Brun
6-7711
Extension wand, Vara de extensión, Rallonge (22180,
22170)
1-5941
Nozzle .5GPM
Tobera
Buse
Turn clockwise to tighten hose clamp.
Repair Parts Kit Gaskets and Seals (not included),
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus) 6-5368
6-3337
Straps
Tirantes
Sangles
6-7742
Extension wand, Vara de extensión, Rallonge (22790)
1-5797
Nozzle .5GPM
Tobera
Buse
2A
2B
22790
22180
22170
Attach nozzle to shut-off handle or extension wand (22180, 22170).
5C
1) Do: Check tightness of hose clamp to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these
conditions are found, replace hose before using. Replace with original manufacturer’s
parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior
and exterior of tank for signs of deterioration of body and bottom. Any sign of
deterioration indicates possible tank weakening and could result in explosive bursting
under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only.
5) Do: Pump plunger 8-10 strokes and inspect for leaks.
6) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
7) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions),
empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.