AMX Mio R-3 - Manual

Quick Start Guide
MIO R-3
Mio Modero ® Remote
Overview
The Mio R-3 remote (FG148-03) provides custom control features, contained in
an elegant handheld rechargeable device. The Mio R-3 communicates with a
NetLinx master via a wireless ZigBee® network. The Mio R-3 is pre-loaded with
firmware that allows joining to ZigBee Pro 2007 networks, but may be upgraded
with firmware allowing access to older ZigBee 2004 networks.
You need VisualArchitect and KeypadBuilder to properly program this device.
The application and documentation are available from www.amx.com.
Touch And Tilt Sensor
The MIO R-3 wakes up upon touching either the chrome side rails or pressing a
button. When the remote times out while holding it, you can reawaken the device
by tilting it. Errant jostling such as a bumped table will not wake the device
unless you are holding it.
Specifications
The MIO R-3 device specifications are as follows:
Installing Your Custom Buttons
1. Flip and turn the MIO R-3 device so that the buttons are facing away from
you and the device is upside down.
2. Holding the device in both hands, place your thumbs on the battery door
and push up to slide the battery door free. The battery door will slide in the
direction of the bottom end of the device.
3. Unscrew the 6 screw points indicated in FIG. 2.
4. Turn the unit over so the buttons are facing you.
5. Lift the top assembly away from the PCB.
6. If necessary, push out the standard buttons from the front of the top assem-
bly.
7. Drop on your custom button pad and verify the alignment with the guide
posts on the PCB.
8. Place the top assembly back down on the PCB and return the unit over,
exposing the 6 screw points.
9. Tighten the 6 screw points.
10. Place the battery door back on the device, and slide the door upwards to
lock it in place.
Inserting the Lithium-Ion Battery into The MIO R-3
To install your Lithium-Ion battery into the MIO R-3 remote:
1.
Flip and turn the device so that the buttons are facing away from you and
the device is upside down.
FIG. 1 The MIO R-3 Device
MIO R-3 (FG148-03) Specifications
Dimensions
(HWD) 9.50 x 2.00 x .74 (241.3 mm x 50.8 mm x 18.80 mm)
Weight • .45 lbs (20 g) without batteries
• .55 lbs (25 g) with batteries
Battery Rechargeable Lithium-Ion
Transmission
Frequencies • Zigbee RF wireless network
• IR 38 Khz
• IR 455 Khz
Transmission
Range • ZigBee: 100 feet (30.48m)
• IR 38 Khz: 100 feet (30.48m)
• IR 455 Khz: 50 feet (15.24m)
Top Components • LED - blue backlit buttons indicate device is awake
• Display (OLED) - 128 x 32 pixels, active area is 29.42mm x
7.98mm
• Pushbuttons - the power button is red backlit; the rest are blue
backlit buttons. 45 buttons; 9 custom buttons (3 macro and 6
device).
1
2 3
4 5
6
7
8 9 10
11
12
13
14
15
16
26 28
Power
Transmission Mode
Current Menu
Battery Meter
Custom Macro
Buttons
Custom Mode
Options
2
1
16 17
10 11
12
18
13 15 14
19
23
21
24
20
22
25 26
4 3
8
6
9
5 7
Numeral Keypad
1 - Power
2 - Record
3 - Pause
4 - Stop
5 - Rewind
6 - Play
7 - Fast Forward
8 - Skip Back
9 - Skip Forward
10 - Menu
11 - Info
12 - Move Up
13 - Move Left 14 - Select
15 - Move Right
16 - Guide
17 - Exit
18 - Move Down
19 - Volume Up
20 - Last Selected
21 - Channel Up
22 - Mute
23 - Volume Down
24 - Channel Down
25 - Input
26 - Enter
MIO R-3 (FG148-03) Specifications (Cont.)
Rear Component • Programming Port - 2.5 mm stereo female conductor jack
• Battery Door
• Rechargeable Battery Connection
Supported
Languages • English
• French
• German
• Greek
• Italian
• Japanese • Korean
• Simplified Chinese
• Portuguese
• Russian
• Spanish
• Other languages supported by Glyphs
Certifications • FCC ID: CWU-NXR-MO
• IC: 5078A-NXRMO
• CE
• IEC-60950
• Japan Approval
• Designed for ZigBee
Operating
Environment • Operating Temperature: 0° to 40° C (32° to 104° F)
• Storage Temperature: -20° to 70° C (-4° to 158° F)
• Relative Humidity: 5% to 85%
Included Items • MIO-RBP Rechargeable Lithium-ion Battery (FG147-10)
Other AMX
Equipment • DB-9 extension cable (FG10-727)
• Programming Cable - a 3 wire, 2.5 mm stereo jack (FG10-817)
• Custom engraving (FG147-01)
• MIO-RCC Kit (FG147-03K)
• MIO-RCC Charging Base (FG147-02)
• NXR-ZGW (FG5791-01)
• NXR-ZRP-PRO (FG5791-03)
FIG. 2 Internal MIO R-3 Components
6 Screw Points
Programming Jack