American Dynamics VideoEdge NVR Bundled Server User Manual

Videoedge ™ nvr bundled server, What’s in the box 1 panel connectors 4 results 6, Required accessories (not in this box)

Advertising
background image

VideoEdge ™ NVR Bundled Server

Standard Items

What’s in the Box

1

Panel Connectors

4

Results

6

IP Network Camera

VGA or Flat Panel Monitor (not shown)

PC with Internet Browser and Network Connection (not shown)

Required Accessories (not in this box)

IP Encoder

Gigabit Switch

2

Power Up and Test

5

The unit should power up as soon as you press the Power button on the front
of the unit.

Reset button

LCD Panel

Power button

Back Panel

Quick Setup Guide and VideoEdge

NVR Installation Disc.

8200-2601-01 B0

© 2008 Tyco International Ltd. and its Respective Companies. All Rights Reserved

VideoEdge™ NVR Bundled Server

NOTE: Store the VideoEdge™ NVR CD and jewel case in
a safe place. The serial number printed on the label is your
proof of license to use the software.

Supported IP Cameras or VideoEdge™ IP Encoders

Gigabit Ethernet switches and cabling

Optional Accessories for Extended Storage

3

American Dynamics Fibre Host Bus Adapter (HBA) Kit*

USB Keyboard

2 x Localized Power Cords

Connect Power and additional cables as indicated above

Be sure to use an Uninterruptible Power Supply (UPS)

Always follow appropriate safety precautions

Unit powers up when you press the Power button on the front panel

Be sure to use surge protection for power supply and provide appropriate

grounding

VGA Monitor and peripherals should be powered up before the unit is

powered up

Connect the VGA Main Monitor

Connect to blue female connector

Connect the USB Keyboard

Connect Gb 1 (LAN1) to Client Network

Connect Gb 2 (LAN2) to Camera Network

Connect both Power Cords

Optional: Connect the Fibre RAID

Storage Unit

Use proper network switch or cross-over cable

Observe the boot sequence on the VGA monitor.

On the client computer launch the Internet browser and enter the IP address
of the VideoEdge™ NVR Bundled Server.

Use proper network switch

The VideoEdge™ NVR Bundled Server should be powered up and running.

The VideoEdge™ web page should be displayed on the client PC.

Is the Unit Functioning as Described?

NO!

If you have checked all these items and the unit fails to power up, or you
repowered your unit and the unit still fails to operate properly, please contact
your American Dynamics Representative.

YES!
The VideoEdge™ NVR Bundled Server is ready to be licensed and configured.

Use the following information to log in:

Default Username: admin

Default Password: admin

You must now register the VideoEdge(tm) NVR Bundled Server to license the
NVR, complete the installation and configure the network, users/groups and
camera configuration settings. For details refer to the User Manual on the
VideoEdge™ NVR Installation Disc.

Is the VideoEdge™ NVR Bundled Server powered up?
Check the power connections.

Did you see the boot sequence on the VGA monitor?
If not, power the VideoEdge™ NVR Bundled Server off and restart. You may
need to re-install the NVR Software.

Can you connect with a browser?
If not, verify the IP address is correct by using the ping command from a
Command Prompt window. Verify the network connections, IP addresses and
subnet masks on the client.

CAUTION: Do not boot the VideoEdge™ NVR Installation

Disc

on your desktop

computer. Booting from this disc removes all data from the primary hard disk.

NOTE: The registered camera license file must be applied to the
VideoEdge™ NVR Bundled Server before the temporary license period expires.

Note: The Fibre HBA Kit is required and sold

separately*

American Dynamics Fibre RAID Storage System*

*Contact your American Dynamics Representative for more information.

Rack Mounting Kit

Advertising