IDEC FL1E SmartRelay User Manual
IDEC Equipment
Advertising
Table of contents
Document Outline
- FL9Y-B1090(6)
- Preface
- Contents
- Getting started with IDEC SmartRelay
- IDEC SmartRelay installation and wiring
- Programming IDEC SmartRelay
- 3.1 Connectors
- 3.2 Blocks and block numbers
- 3.3 From circuit diagram to IDEC SmartRelay program
- 3.4 The four golden rules for operating IDEC SmartRelay
- 3.5 Overview of IDEC SmartRelay menus
- 3.6 Writing and starting the circuit program
- 3.6.1 Selecting programming mode
- 3.6.2 The first circuit program
- 3.6.3 Circuit program input
- 3.6.4 Assigning a circuit program name
- 3.6.5 Password
- 3.6.6 Switching IDEC SmartRelay to RUN mode
- 3.6.7 Second circuit program
- 3.6.8 Deleting a block
- 3.6.9 Deleting block groups
- 3.6.10 Correcting programming errors
- 3.6.11 Selecting analog output values for RUN/STOP transition
- 3.6.12 Defining the type of analog outputs
- 3.6.13 Deleting the circuit program and password
- 3.6.14 Summertime/wintertime conversion
- 3.6.15 Synchronization
- 3.7 Memory space and circuit program size
- IDEC SmartRelay functions
- 4.1 Constants and connectors - Co
- 4.2 Basic functions list - GF
- 4.3 Special functions
- 4.4 Special functions list - SF
- 4.4.1 On-delay
- 4.4.2 Off-delay
- 4.4.3 On-/Off-delay
- 4.4.4 Retentive on-delay
- 4.4.5 Interval time-delay relay/Pulse output
- 4.4.6 Edge-triggered interval time-delay relay
- 4.4.7 Asynchronous pulse generator
- 4.4.8 Random generator
- 4.4.9 Stairwell Light Switch
- 4.4.10 Dual-function switch
- 4.4.11 Seven-day time switch
- 4.4.12 Twelve-month time switch
- 4.4.13 Up/down counter
- 4.4.14 Operating hours counter
- 4.4.15 Frequency trigger
- 4.4.16 Analog trigger
- 4.4.17 Analog differential trigger
- 4.4.18 Analog comparator
- 4.4.19 Analog watchdog
- 4.4.20 Analog amplifier
- 4.4.21 Latching relay
- 4.4.22 Current impulse relay
- 4.4.23 Message texts
- 4.4.24 Softkey
- 4.4.25 Shift register
- 4.4.26 Analog Multiplexer
- 4.4.27 Analog Ramp Control
- 4.4.28 PI controller
- 4.4.29 Pulse Width Modulator (PWM)
- 4.4.30 Analog math
- 4.4.31 Analog math error detection
- Configuring IDEC SmartRelay
- IDEC SmartRelay memory and battery cartridge (card)
- IDEC SmartRelay software
- Applications
- Technical data
- A.1 General technical data
- A.2 Technical data: FL1E-H12RCC/FL1E-B12RCC
- A.3 Technical data: FL1B-M08C2R2
- A.4 Technical data: FL1E-H12SND
- A.5 Technical data: FL1B-M08B1S2
- A.6 Technical data: FL1E-H12RCA/FL1E-B12RCA
- A.7 Technical data: FL1B-M08D2R2
- A.8 Technical data: FL1E-H12RCE/ FL1E-B12RCE and FL1B-M08B2R2
- A.9 Switching capacity and service life of the relay outputs
- A.10 Technical data: FL1B-J2B2
- A.11 Technical data: FL1D-K2B2, FL1D-K2BM2
- A.12 Technical data: Text Display
- Determining the cycle time
- IDEC SmartRelay without display
- IDEC SmartRelay menu structure
- Type Numbers
- Index