Tracer TP-8200A M-L A02179-2 - Manual

TP-8200A UV/Blue ™
12-Volt, ‘‘Instant On,’’ Compact
Leak Detection Lamp
U.S. Patents 5,816,692 and 5,905,268
SAVE THESE INSTRUCTIONS
OPERATION
1. Turn off the engine.
2. Add fluorescent dye to the system. For best results, use
OEM-approved Tracerline ® Fluoro-Lite ® and Dye-Lite ® dyes.
3. Run the engine and/or system for 5 to 10 minutes to circulate
the dye. Turn off the engine.
4. Connect the battery clips to any 12-volt vehicle battery or
regulated 12 VDC, 4.2 amp (minimum) power source.
5. Do not look directly into the UV/blue light. You must wear the
TP-9940 fluorescence-enhancing glasses supplied with the
lamp to protect your eyes and to make leaks clearly visible.
6. Scan the system with the lamp. Leaks will show with a bright
fluorescent glow. The leaks will show best under low light
conditions.
7. After the leaks are repaired, clean off the dye residue with
GLO-AWAY™ dye cleaner and reinspect with the lamp.
TO REPLACE THE FILTER LENS
Use only the TP-8211A filter lens.
1. Twist off the filter lens holder (1) and remove the retaining ring
(3) to release the filter lens.
2. Using a clean cloth, place the new filter lens (2) on the ridge in
the lens holder, black dot facing toward the bulb.
3. Press the retaining ring into the notches in the lens holder.
4. Align the filter lens holder into the notches on the lamp and
twist the holder back into place.
TO REPLACE THE BULB
Use only the 50W TP-8115 bulb. Using any other bulb may
damage the unit and will void the warranty.
1. Remove the filter/lens assembly.
2. Pull the bulb/reflector (4) by its edge to release.
3. Hold the new bulb by the edge of the reflector and press the bulb
into the bi-pin socket (5) firmly, but gently.
4. Twist the filter/lens assembly back into place.
IMPORTANT SAFETY INSTRUCTIONS
1. Read all instructions.
2. Care must be taken as burns can occur from touching hot parts.
3. Do not operate the lamp with a damaged cord or if the lamp has
been damaged.
4. Do not let the cord hang over edge of table, bench or counter, or
come in contact with hot manifolds or moving fan blades.
5. To protect against risk of fire, do not operate the lamp in the
vicinity of open containers of fuel (gasoline).
6. Adequate ventilation should be provided when working on
operating combustion engines.
Do not use below garage floor or grade level.
Ne pas utiliser en fosse ou en dessous du niveau du sol.
WARRANTY
The warranty policy for the lamp is provided on the Certificate
of Limited Warranty enclosed separately with each unit.
NOTE: For assistance of any kind, contact the Customer Service
Department at Tracer Products.
TP-8200A UV/Blue ™
Lampe de détection de fuites taille compacte,
12 volts, à « Fonctionnement instantané »
Brevets US 5,816,692 et 5,905,268
CONSERVEZ CES INSTRUCTIONS
FONCTIONNEMENT
1. Mettez le moteur à l'arrêt
2. Ajoutez du colorant fluorescent au circuit. Afin d'obtenir les
meilleurs résultats, utilisez les colorants Tracerline ® Fluoro-Lite ®
et Dye-Lite ® approuvés constructeur (OEM).
3. Faites fonctionner le moteur et/ou le circuit pendant cinq (5) à dix
(10) minutes afin de faire circuler le colorant. Mettez le moteur à
l'arrêt.
4. Connectez les fiches de connexion à la batterie 12 volts du
véhicule ou à une alimentation 12 volts à courant continu régulée,
4,2 A (minimum).
5. Ne regardez pas directement la lumière émise par UV/blue.
Vous devez porter les lunettes TP-9940 améliorant la
visibilité de la fluorescence qui sont fournis avec la lampe
afin de protéger vos yeux et de rendre les fuites parfaitement
visibles.
6. Balayez le circuit avec la lampe. Les fuites apparaîtront sous
forme d'une fluorescence brillante. Les fuites seront plus
apparentes sous un éclairage faible.
7. Après que les fuites sont réparées, nettoyez les restes de
colorant avec le nettoyant approprié GLO-AWAY™ et procédez
à une nouvelle vérification.
POUR REMPLACER LA LENTILLE DU FILTRE
Utilisez uniquement la lentille pour filtre TP-8211A.
1. Dévissez la monture (1) de la lentille du filtre et déposez l'anneau
de maintien (3) afin de libérer la lentille du filtre.
2. En utilisant un linge propre, appuyez sur le nouveau filtre (2) pour
l'installer dans la monture, le point noir faisant face à l'ampoule.
RACERLINE ® ®
RACERLINE ® ® English
French
WARNING
• RISK OF EXPLOSION. This equipment has internal arcing
or sparking parts that should not be exposed to
flammable vapors. It should be located in an area
providing at least four air changes per hour, or should
be located at least 18 inches above the floor.
• Do not secure the momentary ON/OFF switch in the ON
position. This will void the lamp’s warranty.
• Use for a maximum of 5 minutes and allow a 10-minute
cooling period before restarting.
• Always disconnect the lamp from the power source
and allow it to cool to the touch before storing or
disassembling.
PARTS LIST
ITEM PART NO. DESCRIPTION
1 121599 FILTER LENS HOLDER
2 TP-8211A FILTER LENS, 1.7 IN (4.3 CM) DICHROIC
3 121600 RETAINING RING
4 TP-8115 BULB/REFLECTOR, 50W
5 100090 SOCKET, BI-PIN
6 121597 SWITCH, ROCKER
7 103558 CORD, 12 FT (3.7 M), WITH ALLIGATOR CLIPS