Paasche Airbrush SA-PL User Manual

Sa airbrush, For hobbies & crafts single action / internal mix

Advertising
background image

INSTRUCTION AND PARTS LIST SA-8/31/2011

Supercedes Instruction & Parts List SA-10/30/2008

SA Airbrush

for Hobbies & Crafts

Single Action / Internal Mix

WARNING: Spray materials may be harmful if inhaled or

allowed to come into contact with the skin or eyes. Consult

the product label and Material Safety Data Sheet supplied

for the spray material. Follow all safety precautions.

CAUTION: Well Ventilated Area Required to remove

fumes, dust or overspray. Secure airhose to Airbrush

with V-62 Wrench for safety and to prevent air leaks.

M a x i m u m A i r P r e s s u r e 7 5 P . S . I .

No.

Part No.

Description

1.

VL-189

Head Protecting Cap

3.

VLA-1, 3 or 5

Aircap (Select Size)

4.

VLB

Aircap Body

5.

VLT-1, 3 or 5

Tip (Select Size)

6.

SAN-1, 3 or 5

Needle-Extra Length

7.

SA-206

Finger Button Assembly

8.

VL-135A

Finger Button

9.

SA-207

Finger Button Stem

10.

SA-210

Shell Assembly

VL-20

Valve Casing (Included)

No.

Part No.

Description

11.

SA-208

Handle

12.

SA-211

Needle Chuck

13.

SA-212

Needle Locknut

14.

MU-612

PTFE Packing & Packing Nut (sold
as set)

16.

VL-176

Air Valve Assembly

17.

VL-20

Valve Casing

18.

A-52

Valve Washer (Pack of 6)

19.

H-21A

Valve Plunger

20.

A-22

Valve Spring

21.

A-23A

Air Valve Nut

Printed in the U.S.A.

Paasche Airbrush Company

4311 North Normandy Avenue

Chicago, IL 60634-1395

Phone: 773-867-9191 • Fax: 773-867-9198

Website: paascheairbrush.com

E-Mail: [email protected]

INTRODUCTION:

The SA Airbrush is simple in design and operation. Ideal for
Hobbyists and Crafters that are just learning to use an Airbrush.

OPERATING INSTRUCTIONS:

Adjustments in the flow of color are made by turning the Needle
Chuck (#12) in to decrease, or out for increased flow. To spray,
press the Finger Button (#8).
To disassemble, loosen the Needle Locknut (#13) by holding the
Needle Chuck (#12) firmly so it will not turn. Unscrew the Needle
Chuck from the Red Handle (#11) and remove the Handle. Now
carefully remove the Needle (#6) and then the Finger Button
Assembly. Note: The angled hole in the Finger Button Stem (#9)
as you remove it because it must be replaced with the angle of
the hole in line with the Needle (#6). The Aircap (#3), Aircap Body
(#4) and Tip (#5) may now be removed. Reassembly should
always be done with care, especially when reinserting the
Needle. Reverse the procedure used for disassembly. After the
Needle has been gently pushed forward into the tip, assemble the

Needle Chuck (#12) and screw it in firmly. Hold the Needle Chuck
while screwing the Needle Locknut (#13) down to lock the needle.
Caution should always be used when reinserting the Needle - too
much pressure can damage the tip.

ADJUSTING OR REPLACING WORN PACKING WASHER:

1. If PTFE Packing-#14 becomes worn or loose it must be

tightened or replaced.

2. You will need a small screwdriver to remove or tighten the

Packing Nut.

3. When replacing your PTFE Packing press Packing onto the

Packing Nut-#14. Use a small screwdriver to tighten packing
nut into shell until it is tight then back out one-half turn, may
vary.

4. Now insert needle - you should feel a slight resistance. If too

loose or too tight adjust the Packing Nut with screwdriver until
you feel some slight resistance.

5. Now completely re-assemble guts of Airbrush.

Advertising