Star Water Systems Control Valve - Manual

1
137216
PROGRAMMING THE 5600 “DR” CONTROL VALVE
WARNING: ALWAYS TURN INDEXING KNOB
CLOCKWISE. OTHERWISE, DAMAGE TO THE
VALVE MAY RESULT AND VOID WARRANTY.
A. SET CURRENT TIME OF DAY
1) Plug unit into a 115 volt grounded outlet that is
independent from a wall switch or pull chain.
2) Set present time of day by depressing and holding
in red button on left side of indexing knob (Figure A).
Turn the large hour gear until the actual time of day
is opposite the time of day pointer, noting AM and
PM marking. The regeneration cycle is factory set to
occur at 2 AM.
If a different regeneration time is desired, set the time of day
on the large hour gear ahead or behind the actual time of
day to compensate.
3) Release the red button, making sure the large hour
gear is engaged.
B. SET HARDNESS LEVEL OF THE WATER
Based upon the average national water hardness level, the
valve has been factory pre-set. However, water hardness
will vary by location. For best efficiency, the valve should be
programmed to each specific installation.
If the water source to be treated is city water, call the water
department for the water hardness level. If the water source
is a private well; information concerning the mineral content
(Hardness) can be obtained by purchasing the 136958 mail-
in test kit from your dealer. Return a sample of untreated
water in the bottle provided with the kit to our laboratory. The
water sample will be professionally analyzed and the results
of the analysis will be mailed to you.
1) To program the water hardness level, locate the stick
people wheel (Figure B.)
2) With your thumb and forefinger, grasp the stick people
wheel. Pull the wheel outward and turn until the
number of people in your family matches the water
hardness level.
C. GENERAL INFORMATION
1) Once you have set the people and hardness, this
will automatically set the “White Dot” on the number
of gallons (hundreds of gallons) available as soft
water before the unit needs to regenerate.
2) As you use water in your home, the “White Dot” will
move to the left (counter-clockwise) and subtract
gallons from the available soft water gallons. This is
indicated by reading the “Black Arrow”. This
METER CAPACITY (GALLONS)
TO SET TIME OF DAY-PRESS RED
BUTTON AND TURN LARGE GEAR UNTIL
PRESENT TIME APPEARS ABOVE ARROW.
FOR MANUAL REGENERATION TURN KNOB
CLOCKWISE TO REGEN. POSITION.
TIME
OF DAY
IN SERV.
IL0411
Pc
1234567
HA
R
D
N
E
S
S
10
80 50
40
3
5
3
0
25
20
15
IL0410
RED BUTTON
INDEXING KNOB
LARGE HOUR
GEAR
TIME OF DAY POINTER
STICK PEOPLE
WHEEL
WATER
HARDNESS
WHEEL
FIGURE C
FIGURE A
FW0278
0206
Supersedes
0404
FIGURE B
^
^
^
^
^ ^^
^ ^^ ^ ^
^ ^
^
^
^
^
^
^
^
^
^
^
^
^
^
^
^
^
^
^
^^
^ ^ ^^^^
^^
^
^
^
^
^
^
^
^
^
^
^
^
^
^
Pc
1234567
HA
R
D
N
E
S
S
10
80 50
40
3
5
3
0
25
20
15
X 100 19
1
8
1
7
1
6
1
5
1
4
1
3
12
11 10
9
8
7
6
5
4
3
2
1
STICK PEOPLE
WHEEL
WATER
HARDNESS
WHEEL
GALLONS REMAINING UNTIL
NEXT REGENERATION
“BLACK ARROW”
TRIP ARM
GALLON
WHEEL
AVAILABLE GALLONS OF
SOFT WATER “WHITE DOT”