Satechi Aluminum External Hard Disk Enclosure USB 3.0 & eSATA, Case for 9.5mm & 12.5mm 2.5 SATA-I, SATA-II, SATA-III HDD & SSD - Manual

7 ST-SEHE30 User Manual
Regulatory Compliance
FCC Class B Information
This device has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This unit generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio or television reception. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, you are encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/television technician for help.
Any changes or modifications not expressly approved by Satechi could void the user’s authority to
operate this equipment.
CE
This equipment has been tested and found to comply with the limits of the European Council
Directive on the approximation of law of the member states relating to electromagnetic
compatibility (89/336/EEC) according to EN 55022 Class B.
Limited Warranty
Satechi warrants this product to be free from defects in materials and workmanship for 1 year. If
this product is found to be defective within that time, we will repair or replace it. This warranty does
not cover accidental damage, wear and tear, or consequential or incidental loss. Under no
conditions is Satechi liable for loss of, or damage to devices; nor loss of, or damage to, programs,
records, or data; nor any consequential or incidental damages, even if Satechi has been informed
of their possibility. This warranty does not affect your statutory rights.
If you have any questions, comments, or concerns about your Satechi product, please contact us
first.
Phone: 858-268-1800
Email: [email protected]
www.satechi.net
©2012 SATECHI
ST-SEHE30 User Manual 6
Wiring Instructions
e-SATA: connect one end of the e-SATA cable to the enclosure, then connect the
other end to your computer.
USB3.0: connect the “Y” end of the USB3.0 cable to the enclosure, then connect
the other end to your computer.
e-SATA cable
USB3.0 cable
USB3.0 “Y” end
CAUTION!
• Enclosure may reach external temperature of 50°C. Please handle with care.
• Move and install the drive by handling the sides; do NOT touch the circuitry.
• Do NOT disconnect the device from your computer without ejecting first. To do this, right click
the drive in “My Computer” and click “eject.”
• When installing drive into the enclosure, ensure the SATA connecters are in line. Do not use
excessive force during installation.
• Read your drive’s manual before installation.
• Avoid blunt force to the device and avoid storing the device in hot or humid areas.
5 ST-SEHE30 User Manual
Installation Instructions Continued
4. Swing swivel arm in.
5. Slide and depress button, then push
swivel arm into place.
6. Device is ready to use.
Do not use excessive force; if the device is resistant
to close make sure the drive is inserted correctly.
ST-SEHE30 User Manual 4
Installation Instructions
1. Push and slide button on top of device.
2. Swing swivel arm out.
3. Insert supported drive as shown, with
SATA connecter on bottom.
Product Diagram
3 ST-SEHE30 User Manual
1. Open / Close button
2. USB3.0 output
3. LED indicator
4. e-SATA out
Front
Top
Bottom
Product Overview
Introducing the Satechi External HDD Enclosure, a hard drive casing that supports 9.5mm and
12.5mm 2.5" SATA HDD and SSD. The HDD Enclosure supports a variety of output methods to suit
your needs, including USB3.0, USB2.0, and e-SATA. The Enclosure requires no tools to set up your
drive, and can be installed and used in a matter of seconds, offering quick and easy drive
swapping. A sturdy, sleek brushed aluminum design ensures your data will be protected while
maintaining a high form factor.
Features
• USB3.0 / USB2.0 / e-SATA connectivity
• Usable with 9.5mm and 12.5mm drive thickness
• Supports 2.5” SATA HDD / SSD
• Tool-free set up for easy installation and swapping
• Thick, sturdy casing protects your data
• Sleek brushed aluminum design, portable
• LED power indicator
• Plug-and-play with Mac and Windows computers
Specifications
Components
Product Model
Drives Supported
Materials
Color
Dimensions
Weight
Output
System Req.
Hot-Swap
ST-SEHE30
2.5" SATA HDD / SSD
9.5mm / 12.5mm thickness
Plastic, Metal
Black, Silver
132mm x 90mm x 18.5mm
190g
USB3.0, USB2.0, e-SATA
Windows 98/ME/2000/XP/Vista/7 Mac 9.1/10.2 or above
Supported
HDD Enclosure
User Manual
USB3.0 Y Cable
e-SATA Cable 1
1
1
1
ST-SEHE30 User Manual 2
EXTERNAL
HDD Enclosure User Manual
ST-SEHE30