Warning, Temperature and moisture, Ice and water – Amana W10316638A Manuel d'utilisation

Page 10

Advertising
background image

10

Temperature and Moisture

Temperature is too warm

New installation? Allow 24 hours following installation for the
refrigerator to cool completely.

Door(s) opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully
closed.

Large load of food added? Allow several hours for
refrigerator to return to normal temperature.

Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See “Using the Controls.”

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

Humid room? Contributes to moisture buildup.

Door(s) opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully
closed.

Ice and Water

The ice maker is not producing ice or not enough ice

Refrigerator connected to a water supply and the supply
shutoff valve turned on?
Connect refrigerator to water
supply and turn water shutoff valve fully open.

Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.

New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.

Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.

Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil. (This
does not apply to models with the ice maker mounted at the
top of the freezer door.)

Reverse osmosis water filtration system connected to
your cold water supply?
This can decrease water pressure.
See “Water Supply Requirements.”

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

Water shutoff valve not fully open? Turn the water shutoff
valve fully open.

Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

Reverse osmosis water filtration system connected to
your cold water supply?
This can decrease water pressure.
See “Water Supply Requirements.”

Questions remain regarding water pressure? Call a
licensed, qualified plumber.

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections
can cause discolored or off-flavored ice.

Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ice.

Odor transfer from food? Use airtight, moisture-proof
packaging to store food.

Are there minerals (such as sulfur) in the water? A water
filter may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator? Gray or
dark discoloration in ice indicates that the water filtration
system needs additional flushing.

The ice dispenser will not operate properly

Freezer door closed completely? Close the door firmly. If it
does not close completely, see “The doors will not close
completely.”

Ice bin installed correctly? Be sure the ice bin is firmly in
position.

New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.

Ice clogged in the ice storage bin or delivery chute?
Remove clogged ice, using a plastic utensil if necessary.
Clean chute and bottom of storage bin using a warm moist
cloth, and dry both thoroughly. To avoid clogging and maintain
a fresh supply of ice, empty the storage bin and clean both the
bin and delivery chute every two weeks.

Has the wrong ice been added to the bin? Use only cubes
produced by the current ice maker.

Has the ice melted around the auger (metal spiral) in the
ice bin?
Empty the ice container. Use warm water to melt the
ice if necessary.

Is the ice dispenser stalling while dispensing “crushed”
ice?
Change the ice button from “crushed” to “cubed.” If
cubed ice dispenses correctly, depress the button for
“crushed” ice and begin dispensing again.

Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

WARNING

Advertising