Timeguard IR10 User Manual

Ir remote control ir-10 instructions 1, Package contents, Features

Advertising
background image

Model IR-10

• Adjustments can only be made in Unlocked Mode.

• By use of the button the operational settings mode for one unit

can be loaded into other units in the same area.
It also allows return to previous operational settings after a Reset.

• The maximum IR transmit time when a button is pressed is 1 second,

pressing a button for longer than this is not effective.

• Pressing more than one button simultaneously will result in a failed

transmission.

• Commands and operational settings are all confirmed by around

2 seconds of rapid flashing of the sensor LED except for
(see relevant section).

• Time setting for load II (HVAC) is only available with PDSM362 and

PDFM362.

Push

Button

Function

Sensor load I ON

• By pressing the “

“ button load I will be switched

IR Remote Control IR-10 Instructions

1

Package Contents

4

Push Button Function

Technical Specifications
Rated Voltage:

3V DC (CR2032 battery)

Transmission Range: Approx.

3M

Transmission Angle: 35º
Operating Temperature:

0ºC to +45ºC

Storage Temperature:

-25ºC to +55ºC

Conforms To EC Directives

Note

IR_10_Instructions.indd 1

14/3/08 15:21:32

Model IR-10

2.1 No need for climbing up ladders, the ceiling mounted presence

detector can be adjusted and set up easily by a user with an IR-10.

2.2 By pressing “ “ button the actual light level can be read-in to

the sensor. (Refer to function of “ “ button).

2.3 The IR-10 can be attached to a

key ring chain for convenience.
(See Fig.1)

2.4 To render the IR-10 operational

remove the battery isolating
strip by pulling the exposed
tab away from the IR-10 body.

Lever out the battery holder with a screwdriver, then replace the battery
(type CR2032 3V). Please make sure the battery is the right way up,
then push the battery holder back. (See Fig.2)

• Adjustments can only be made in Unlocked Mode.

• The sensor may be set to continuously ON or OFF for 8 hours as well

as detection mode controlled by or independent of light level.

• By use of the button the operational settings made for one unit

can be loaded into other units in the same area.
It also allows return to previous operational settings after a Reset.

• The maximum IR transmit time when a button is pressed is 1 second,

pressing a button for longer than this is not effective (except ).

• Pressing more than one button simultaneously will result in a failed

transmission.

• Commands and operational settings are all confirmed by around

2 seconds of rapid flashing of the sensor LED except for
(see relevant section).

• Time setting for load II (HVAC) is only available with PDSM362 and

PDFM362.

Push

Button

Function

Sensor load I ON

• By pressing the “ “ button load I will be switched

on for 8hrs, this is confirmed by around 2sec rapid
flashing of the sensor LED. The sensor LED flashes 1sec
ON and 5sec OFF during the ON mode. No movement
can be detected by the sensor during the ON mode.

• Exit the ON mode and return to Auto mode either by

pressing the “ “ button (confirmed by around 2sec
rapid flashing of the sensor LED) or by re-supplying
power after it has been turned off for at least 10 seconds.

• Load I can be switched to the OFF mode by pressing

the “ “ button during an ON period (confirmed by
around 2sec rapid flashing of the sensor LED).

Sensor load I OFF

• By pressing the “ “ button load I will be switched

off for 8hrs, (confirmed by around 2sec rapid flashing
of the sensor LED). The sensor LED flashes 1sec ON and
5sec OFF during the OFF mode. No movement can be
detected by the sensor during the OFF mode.

• Exit the OFF mode and return to Auto mode either by

pressing “ “ or to re-supply power after it has been
turned off for at least 10sec.

• Load I can be switched to the ON mode by pressing

the “ “ button during an OFF period (confirmed by
around 2sec rapid flashing of the sensor LED).

Locking of IR-10

• By pressing the “ “ button the IR-10 can be locked

and no button will function except “ “. It is confirmed
by around 2sec rapid flashing of the sensor LED.

Unlocking of IR-10

• By pressing the “ “ button the IR-10 is unlocked,

(all buttons will now function). This is confirmed by
around 2 sec rapid flashing of the sensor LED.

IR Remote Control IR-10 Instructions

1

Package Contents

2

Features

3

Battery Replacement

4

Push Button Function

Visual I.D.

Item

Remote Control

Instructions

Quantity

1 1

Technical Specifications

Rated Voltage:

3V DC (CR2032 battery)

Transmission Range:

Min. 4m (IR-10 directly below detector)

Transmission Angle:

35º (above range is reduced to approx.

3m at extremes of transmission angle)

Operating Temperature:

0ºC to +45ºC

Storage Temperature:

-25ºC to +55ºC

Conforms To EC Directives

Key Chain

Hole

Fig. 1

Fig. 2

Note

(Command)

(Command)

(Command)

(Command)

IR_10_Instructions_1.4.indd 1

IR_10_Instructions_1.4.indd 1

14/5/08 09:07:19

14/5/08 09:07:19

Advertising