AMX Dual COM Port Card NXC-COM2 - Manual

Installation Guide
NXC-COM2
Dual COM Port Card, 2 RS-232/422/485
NetLinx Control Cards and NetModules
NetLinx Control Cards can be installed in either the NXF CardFrame, NI-4000, or
NetModules. For detailed information on the cards, refer to the NetLinx CardFrame,
Control Cards, and NetModules Instruction Manual available on-line via
www.amx.com.
NXC-COM2 Specifications
The NXC-COM2 Dual COM Port Control Card provides two RS-232/422/485 control
ports and LED feedback for remote sources connected to the NetLinx CardFrame,
NI-4000, or NetModule:
NXC-COM2 Pinouts and Wiring Information:
NXC-COM2 Channel Assignment:
Channel 255 is the CTS (Clear To Send) push channel. It reflects the state of the CTS
input if a 'CTSPSH' command was sent to the device.
NXC-COM2 Programming Information:
FIG. 1 NXC-COM2 Dual COM Port Control card
NXC-COM2 (FG 2022) Specifications
Power Requirements: 140 mA @ 12 VDC
Operation: Data 1-2: Two RS-232/422/485 control ports, supports
XON/XOFF, CTS/RTS
Status LEDs
(2 per channel): • Red LEDs show TX (transmit) data activity
• Yellow LEDs show RX (receive) data activity
- LED 1: CH1 TX (red)
- LED 2: CH1 RX (yellow)
- LED 3: CH2 TX (red)
- LED 4: CH2 RX (yellow)
• Green ICSP status LED (located on the board):
- On = card is not in communication with the Master.
- Blinks (1-second intervals) during normal operation.
Connections/wiring: Two 10-pin 3.5 mm captive-screw terminals
DEVICE_ID: $0107
NXC-COM2 Pinouts NXC-COM2 Wiring Configuration
Pin Signal Function RS-232 RS-422 RS-485
1 GND Signal ground X X
2 RXD1 Receive data X
3 TXD1 Transmit data X
4 CTS1 Clear to send X
5 RTS1 Request to send X
6 TX1+ Transmit data X X (strap to pin 8)
7 TX1- Transmit data X X (strap to pin 9)
8 RX1+ Receive data X X (strap to pin 6)
9 RX1- Receive data X X (strap to pin 7)
10 +12 VDC Power Optional Optional
11 GND Signal ground X X
12 RXD2 Receive data X
13 TXD2 Transmit data X
14 CTS2 Clear to send X
15 RTS2 Request to send X
16 TX2+ Transmit data X X (strap to pin 18)
17 TX2- Transmit data X X (strap to pin 19)
18 RX2+ Receive data X X (strap to pin 16)
19 RX2- Receive data X X (strap to pin 17)
20 +12 VDC Power Optional Optional
ICSNET Status LED
LED 1
LED 4
NXC-COM2 Send_Commands
B9MOFF
Disable 9-bit in
232/422/455 mode.
This command works in
conjunction with the
B9MON command. Syntax:
SEND_COMMAND <DEV>,"'B9MOFF'"
Example:
SEND_COMMAND SOMEDEVICE_1,"'B9MOFF'"
Sets the port settings on SOMEDEVICE to match the port's
configuration settings.
B9MON
Enable 9-bit in
232/422/455 mode.
This command works in
conjunction with the
B9MOFF command. Syntax:
SEND_COMMAND <DEV>,"'B9MON'"
Example:
SEND_COMMAND SOMEDEVICE_1,"'B9MON'"
Resets the SOMEDEVICE port's communication parameters to
nine data bits and one stop bit.
CHARD
Set the delay time
between all transmitted
characters to the value
specified (in 100 micro-
second increments). Syntax:
SEND_COMMAND <DEV>,"'CHARD-<Time>'"
time: 0 - 255. Measured in 100 microsecond increments.
Example:
SEND_COMMAND RS232_1,"'CHARD-10'"
Sets a 1-millisecond delay between all transmitted characters.
CHARDM
Set the delay time
between all transmitted
characters to the value
specified
(in 1 millisecond
increments). Syntax:
SEND_COMMAND <DEV>,"'CHARDM-<Time>'"
time: 0 - 255. Measured in 1 millisecond increments.
Example:
SEND_COMMAND RS232_1,"'CHARDM10'"
Sets a 10-millisecond delay between all transmitted
characters.
CTSPSH
Enable Pushes,
Releases, and status
information to be reported
via channel 255 using the
CTS hardware handshake
input. If Clear To Send (CTS) is set high, then channel 255 is On.
Syntax:
SEND_COMMAND <DEV>,"'CTSPSH'"
Example:
SEND_COMMAND RS232_1,"'CTSPSH'"
Sets the RS232_1 port to detect changes on the CTS input.
CTSPSHOFF
Disable Pushes,
Releases, and Status
information to be reported
via channel 255. Syntax:
SEND_COMMAND <DEV>,"'CTPSH OFF'"
Example:
SEND_COMMAND RS232_1,"'CTSPSH OFF'"
Disables the RS232_1 port to detect changes on the CTS
input.
GET BAUD
Get the RS-232/422/485
port’s current
communication parame-
ters.
Device sends the
response out the Master
program port. Syntax:
SEND_COMMAND <DEV>,"'GET BAUD'"
Example:
SEND_COMMAND RS232_1,"'GET BAUD'"
Device responds with:
<port #>,<baud>,<parity>,<data>,<stop>
485 <ENABLED | DISABLED>
HSOFF
Disable hardware
handshaking (default). Syntax:
SEND_COMMAND <DEV>,"'HSOFF'"
Example:
SEND_COMMAND RS232_1,"'HSOFF'"
Disables hardware handshaking on the RS232_1 device.
HSON
Enable RTS
(ready-to-send) and CTS
(clear-to-send) hardware
handshaking. Syntax:
SEND_COMMAND <DEV>,"'HSON'"
Example:
SEND_COMMAND RS232_1,"'HSON'
Enables hardware handshaking on the RS232_1 device.
RXCLR
Clear all characters in the
receive buffer waiting to
be sent to the Master. Syntax:
SEND_COMMAND <DEV>,"'RXCLR'"
Example:
SEND_COMMAND RS232_1,"'RXCLR'"
Clears all characters in the RS232_1 device's receive buffer.
RXOFF
Disable the transmission
of incoming received
characters to the Master
(default). Syntax:
SEND_COMMAND <DEV>,"'RXOFF'"
Example:
SEND_COMMAND RS232_1,"'RXOFF'"
Stops the RS232_1 device from transmitting received
characters to the Master.