Auerswald 2206 USB User Manual
Isdn pbx systems, Operator´s manual
Advertising
Table of contents
Document Outline
- Table of Contents
- Introduction
- Telephoning
- You like to react to an inbound Call
- You like to make an internal Call
- You like to make an external Call (Call via Exchange Line)
- You like to separate the Charges of external Calls to different Accounts
- The called Person does not take the Call
- You are Dialling a Number and are Hearing the busy Tone
- Start Recall on Busy for internal Telephone Call
- Starting Recall on Busy via Public Exchange for external Connection (CCBS)
- Reserve Exchange Line for the next Call on busy Exchange Lines
- Start a Priority Call to a Telephone protected by the Do-Not-Disturb Service
- The Subscriber called in a Query is busy - Finishing the Call
- You are in a Conversation
- You are in a Call and like to Transfer it
- Transfer a Call with prior Notice
- Transfer external Call without Announcement to an internal Telephone (Blind Transfer)
- Transfer an external Call to a currently unknown internal Target (Open Query)
- Transfer external Call to an external Connection (External to External Transfer)
- Calling an internal third Calling partner and transfer to the second calling Partner
- You have two Calls (Query Call)
- You have a Conference Call
- Talking to a Visitor at the Door (Door Terminal Call)
- You like to take an Emergency Call
- Settings
- You like to use different PBX Configurations (Day, Night etc.)
- You like to stay reachable during your Calls
- You do not like to present your Telephone Number to the Called Party
- Somebody should be reachable for internal/external Callers to your Telephone Number (Subscriber Call Forwarding)
- Forward Telephone „unconditional“ to an internal/external Telephone because you are absent
- Forward Telephone „on Busy“ to an internal/external Telephone because you are currently Telephoning
- Forward Telephone „on no Reply“ to an internal/external Telephone in Case of a short Absence
- Switch the already configured Subscriber Call Forwarding on/off
- Switch off all active Subscriber Forwarding Settings for the Telephone
- Receive Calls at another internal Telephone (Follow-me)
- Programming Subscriber Call Forwarding via an external Telephone if you are „Out of Office“
- External Callers should always reach Somebody when calling your external Number (MSN/DDI Call Forwarding)
- Forward Exchange Line Number „unconditional“ to an external Telephone because nobody is there
- Forward Exchange Line Number „on Busy“ to an external Telephone if the internal Telephones are busy at the Moment
- Forward an Exchange Line Telephone Number „on no Reply“ in Case of a short Absence
- Switch the already configured MSN/DDI Call Forwarding on/off for an Exchange Line Telephone Number
- Switch off all active MSN/DDI Call Forwarding Settings for one Exchange Line Number
- Program MSN/DDI Call Forwarding from an external Telephone if you are „Out of Office“
- You do not like to be called
- You like to save Call Charges with Least Cost Routing (LCR)
- You like to control Call Charges
- You like to retrieve and analyse Call Charge Data
- You like to use the Serial Interface for Special Functions
- You like to simplify the Dialling of external Numbers
- You like to use the Wake-up Function of the PBX
- You like to configure internal Dial Tones and listen to the Result
- You like to configure Ringer Rhythms and listen to the Result
- Make a Call without any Dialling Operation (Automatic Dialling / Hot Line)
- You want to listen into a Room (Room Monitoring)
- Door Terminal Calls should always reach you
- Use the Remote Switching Relay (via Telephone)
- You like to use the Security Functions
- You like to change the Music on Hold/Announcement
- Recording internal Music on Hold with the PBX (COMpact 4410 USB and COMmander Basic only)
- Recording the Music on Hold Announcement via Telephone (COMmander Basic only)
- Configure and mix Music on Hold and Announcement
- Configure the Delay Time between Announcements
- Select and listen to internal Music on Hold (COMpact 4410 USB and COMpact 2206 USB only)
- Listen to Music on Hold and Announcements
- Record the Alarm Announcement by Telephone and listen to it (COMpact 4410 USB and COMmander Basic only)
- You like to set Date and Time
- You like to park Calls with a Parking Code
- Special Functions for Business Applications
- Reception and Secretary Function and Text before Answering
- Use Call Data to separate Call Charges
- Announcements via Loudspeaker and System Telephones
- Save Money and get Information away from Home
- Call Groups (Teams)
- Log in/out as a Member of a Group if you are only Member of one Group
- Log in/out as a Member of a Group if you are Member of several Groups
- Log out all Members of a single Group
- Forward Group „unconditional“ to an internal/external Telephone because all Group Members are absent
- Forward Group „on Busy“ to an internal/external Telephone because all Telephones „logged in“ are currently Telephoning
- Forward Group „on no Reply“ to an internal/external Telephone because all Group Members are absent for a Moment
- Forward Group „if all Subscribers are logged out“ to e.g. an Answering Machine
- Switch a previously configured Group Call Forwarding on/off
- Switch off all active Call Forwarding Settings for one Group
- Program Group Call Forwarding with an external Telephone if you are „Out of Office“
- Hotel Functions for Reception and Room Telephones
- Installation and Use of the bundled Software
- Service Functions, Troubleshooting
- Digit Code Index
- Index