GE JK3500SFSS - Manual

Listed by
Underwriters
Laboratories
JK3500SF
GE ® 27" Built-In Double Wall Oven
Specification Created 2/13 320380
For answers to your Monogram ® or GE appliance
questions, visit our website at geappliances.com
or call GE Answer Center
® service, 800.626.2000.
Note: Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least a 194°F
temperature rating.
Note: If marks, blemishes or the cutout opening is
visible above the installed oven, it may be necessary
to add wood shims under the runners and front
trim until the marks or openings are covered.
Note: Door handle protrudes 3" from door face.
Cabinets and drawers on adjacent 45° and 90°
walls should be placed to avoid interference with
the handle.
Electric wall ovens are not approved for
installation with a plug and receptacle.
They must be hard wired in accordance
with installation instructions.
Dimensions and Installation Information (in inches)
PK7500
JK5500
JK3500
Cabinet 30"
A – Overlap of oven at top of cutout 1"
B – Overlap of oven over side of edges of cutout 3/4"
C – Overlap of oven at bottom of cutout 1-1/4"
Oven
D – Overall depth with handle
27"
Overall depth without handle 23-5/8"
E – Overall height with trim 52-15/16"
F – Overall width 29-3/4"
23" minimum
door opening
allowance
Cutout depth
23-1/2" MIN
8-3/4" MAX.
44" to
bottom of
junction box
22"
D
F
E
Conduit
40"
Junction box
location
CL
Suitable
bracing
to support
runners
(must support 375 lbs.)
2 x 4 or
equivalent runners
level with bottom of cutout
and flush with sides of cutout
or solid bottom floor.
B
27''
A
C
Cutout width
25" MIN.
25-1/4" MAX.
Recommended
minimum
cutout location
from the floor
13-1/4"
Cutout height
49-11/16" MIN.
50-1/8" MAX.
PK7500
JK5500
JK3500
Cabinet 30"
A – Overlap of oven at top of cutout 1"
B – Overlap of oven over side of edges of cutout 3/4"
C – Overlap of oven at bottom of cutout 1-1/4"
Oven
D – Overall depth with handle
27"
Overall depth without handle 23-5/8"
E – Overall height with trim 52-15/16"
F – Overall width 29-3/4"
23" minimum
door opening
allowance
Cutout depth
23-1/2" MIN
8-3/4" MAX.
44" to
bottom of
junction box
22"
D
F
E
Conduit
40"
Junction box
location
CL
Suitable
bracing
to support
runners
(must support 375 lbs.)
2 x 4 or
equivalent runners
level with bottom of cutout
and flush with sides of cutout
or solid bottom floor.
B
27''
A
C
Cutout width
25" MIN.
25-1/4" MAX.
Recommended
minimum
cutout location
from the floor
13-1/4"
Cutout height
49-11/16" MIN.
50-1/8" MAX.
PK7500
JK5500
JK3500
Cabinet 30"
A – Overlap of oven at top of cutout 1"
B – Overlap of oven over side of edges of cutout 3/4"
C – Overlap of oven at bottom of cutout 1-1/4"
Oven
D – Overall depth with handle
27"
Overall depth without handle 23-5/8"
E – Overall height with trim 52-15/16"
F – Overall width 29-3/4"
23" minimum
door opening
allowance
Cutout depth
23-1/2" MIN
8-3/4" MAX.
44" to
bottom of
junction box
22"
D
F
E
Conduit
40"
Junction box
location
CL
Suitable
bracing
to support
runners
(must support 375 lbs.)
2 x 4 or
equivalent runners
level with bottom of cutout
and flush with sides of cutout
or solid bottom floor.
B
27''
A
C
Cutout width
25" MIN.
25-1/4" MAX.
Recommended
minimum
cutout location
from the floor
13-1/4"
Cutout height
49-11/16" MIN.
50-1/8" MAX.
23" minimum
door opening
allowance
Cutout depth
23-1/2" MIN
8-3/4" MAX.
44" to
bottom of
junction box
22"
D
F
E
Conduit
40"
Junction box
location
CL
Suitable
bracing
to support
runners
(must support 375 lbs.)
Cabinet 27"
A – Overlap of oven at top of cutout 1"
B – Overlap of oven over side of edges of cutout 1"
C – Overlap of oven at bottom of cutout 1"
Oven
D – Overall depth with handle
26-23/32"
E – Overall height with trim 52-1/8"
F – Overall width 26-23/32"
JK3500
2 x 4 or
equivalent runners
level with bottom of cutout
and flush with sides of cutout
or solid bottom floor.
B
27''
A
C
Cutout width
25" MIN.
25-1/4" MAX.
Recommended
minimum
cutout location
from the floor
13-1/4"
Cutout height
49-11/16" MIN.
50-1/8" MAX.
KW Rating
240V 7.2
208V 5.4
Breaker Size
240V 30 Amps
208V 30 Amps
Installation Information: Before installing, consult
instructions packed with product for current
dimensional data.