GE DSKS333ECWW - Manual

MATERIALS YOU WILL NEED
WARNING
RISK OF FIRE
• To reduce the risk of severe injury or death, follow all installation
instructions.
‡&ORWKHV GU\HU LQVWDOODWLRQ PXVW EH SHUIRUPHG E\ D TXDOL¿HG
installer.
• Install the clothes dryer according to these instructions and
in accordance with local codes. In the absence of local codes,
installation must comply with the NATIONAL ELECTRICAL
CODE, ANSI/NFPA NO. 70.
• This dryer must be exhausted to the outdoors.
• Use only 4” rigid metal ducting for exhausting the clothes dryer to
the outdoors.
‡'2 127 LQVWDOO D FORWKHV GU\HU ZLWK ÀH[LEOH SODVWLF GXFWLQJ
PDWHULDOV ,I ÀH[LEOH PHWDO VHPLULJLG RU IRLOW\SH  GXFW LV
installed, it must be UL listed and installed in accordance with
the instructions found in “Connecting The Dryer To House Vent”
on page 4 of this manual. Flexible venting materials are known
to collapse, be easily crushed, and trap lint. These conditions will
REVWUXFWGU\HUDLUÀRZDQGLQFUHDVHWKHULVNRI¿UH
• Do not install or store this appliance in any location where it
could be exposed to water and or weather.
‡6DYH WKHVH LQVWUXFWLRQV ,QVWDOOHUV  %H VXUH WR OHDYH WKHVH
LQVWUXFWLRQVZLWKWKHFXVWRPHU 
DETERMINE ELECTRICAL REQUIREMENTS FOR YOUR DRYER MODEL
‡7KLVGU\HUPXVWEHFRQQHFWHGWRDQLQGLYLGXDOEUDQFKFLUFXLWRISURSHUYROWDJHDQGIUHTXHQF\DVVSHFL¿HGRQ5DWLQJ3ODWH ORFDWHGLQVLGH
GU\HUGRRU ZLWKQRRWKHUDSSOLDQFHVRU¿[WXUHVDWWDFKHG
(;&(37,21
‡$ 9 UHFHSWDFOH LV ORFDWHG RQ WKH EDFN RQ WKH GU\HU DQG LV DYDLODEOH RQO\ IRU XVH ZLWK D ZDVKHU WKDW LV DȻ[HG WR WKH GU\HU ZLWK D
:')NLW,WPD\QRWEHXVHGIRUDQ\RWKHUDSSOLDQFHRUDQ\FRQGLWLRQVRWKHUWKDQVWDWHGDERYH 9 9PRGHOVRQO\ 
‡%UDQFKFLUFXLWPXVWEHSURWHFWHGE\WKHUHTXLUHGWLPHGHOD\IXVHVRUFLUFXLWEUHDNHUV9RU9LQVWDOODWLRQDPSV9LQVWDOODWLRQRUDPSV
• The electrical installation must conform to the national and local codes.
208V AND 240V MODELS ARE NOT APPROVED FOR 120V INSTALLATION.
Installation Instructions (USA only)
MODELS DSKS433 AND DSKS333 MUST BE INSTALLED WITH CONTROL PANEL AT BOTTOM IN ORDER TO OPERATE ADEQUATELY.
UNPACKING AND PREPARING FOR INSTALLATION
† Prepare the area and exhaust for installation of new dryer.
† &KHFNDQGHQVXUHWKHH[LVWLQJH[WHUQDOH[KDXVWLVFOHDQDQGPHHWVDWWDFKHGLQVWDOODWLRQVSHFL¿FDWLRQV
† Remove the literature and accessories bag from the dryer drum. Place the literature in a convenient place.
† Using foam pads from dryer carton, turn dryer upside down as shown.
† Install knobs. For location, refer to the Owner’s Manual.
† Dryer is now ready to be mounted above washer using accessory kit.
† Remove the foam shipping pads from under dryer.
† Move the dryer to the desired location.
† Follow the steps in the following pages to connect the dryer to the external exhaust and power supply.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT-
Save these instructions for local
inspector’s use.
•
IMPORTANT-
Observe all governing codes and
ordinances.
• Note to Installer -%HVXUHWROHDYHWKHVHLQVWUXFWLRQV
with the customer.
• Note to Customer - Keep these instructions with your
Owner’s Manual for future reference.
‡%HIRUH WKH ROG GU\HU LV UHPRYHG IURP VHUYLFH RU
discarded, remove the dryer door.
• Service information and the wiring diagram are located
in the control console.
• Do not allow children on or in the appliance. Close
supervision of children is necessary when the appliance
is used near children.
‡,QVWDOO WKH GU\HU ZKHUH WKH WHPSHUDWXUH LV DERYH ƒ)
for satisfactory operation of the dryer control system.
• Product failure due to improper installation is not
covered under the Warranty.
‡'U\HUV LQVWDOOHG LQ JDUDJHV LI DOORZHG E\ ORFDO FRGHV 
PXVWEHHOHYDWHGLQFKHV FP DERYHWKHÀRRU
TOOLS YOU WILL NEED
SLIP JOINT PLIERS FLAT BLADE AND PHILLIPS SCREWDRIVERS
GLOVES
SAFETY
GLASSES
DRYER POWER
CORD KIT
(NOT PROVIDED
WITH DRYER)
4" DUCT
CLAMPS (2)
OR
4" SPRING
CLAMPS (2)
EXHAUST
HOOD
3/4" STRAIN RELIEF
UL RECOGNIZED
4" DIA. METAL
ELBOW
4" DIA. FLEXIBLE METAL (SEMI-RIGID)
UL LISTED TRANSITION DUCT (IF NEEDED)
KIT WX08X10077 (INCLUDES 2 ELBOWS)
4" DIA. METAL DUCT (RECOMMENDED)
4" DIA. FLEXIBLE METAL (FOIL TYPE)
UL LISTED TRANSITION DUCT (IF NEEDED.) DUCT TAPE
UL RATED
120/240V,30A
WITH 3 OR 4 PRONGS.
IDENTIFY THE PLUG
TYPE AS PER THE
HOUSE RECEPTACLE
BEFORE PURCHASING
LINE CORD.
234D2017P001 31-16710 02-13 GE
STACKING KITS FOR DRYERS
(Comes with individual Installation Instructions)
† Over washer
- Use Wall Mount Kit WMK-35 or
- Stack Rack DSDR24 or
- Stack Rack DSR-24
† For alcove and closet depth and width
UHTXLUHPHQWVVHHVSHFL¿FNLWLQVWUXFWLRQV
† All stacking kits are available from your
local sales outlet.
Questions? Call: 800.GE.CARES (US) or visit our web site at: www.GEAppliances.com (US)
Printed in Mexico