Maxsa Innovations Battery-Powered Motion-Activated Outdoor Night-Light - Manual

Model #: 40341 (white)
40342 (dark bronze)
ASSEMBLY AND INSTRUCTION GUIDE
• Light where you need it most! Your Outdoor Night-Light™ will guide you
every step of the way.
• Perfect for both indoor and outdoor use. Place your Outdoor Night-Light™
outdoors by the entrance door, and you won’t fumble for your keys or the
lock anymore. Place it indoors and you no longer have to enter your house
in the dark.
• Use it outdoors for steps, doors, walkways, porches, gates, sheds, decks
and more.
• Use it indoors for hallways, bathrooms, steps, and any other dark spaces
you can imagine.
• The three brilliant LEDs will light your way, preventing you from falling down
the stairs or tripping over objects. Great for lighting up dark areas.
• Totally portable and needs no wiring. Uses 3 AA batteries (not included),
which will last 6-12 months depending on usage.
ABOUT YOUR OUTDOOR NIGHT-LIGHT ™
1. To access the battery compartment, slide the tab on the bottom of
the mounting plate to “Open” and slide down the mounting plate
on the back side of your Outdoor Night-Light™. If the mounting
bracket does not slide, please make sure mounting lock is
positioned towards the back side of the unit.
2. Then push up the tab of the battery
cover inside and replace the batteries
according to the orientation noted in
Diagram 2.
Your Outdoor Night-Light™ uses
three AA batteries. The batteries
typically last 6 months to 1 year under
normal use.
Note: If your Outdoor Night-Light™ does not turn on after
battery installation: Make sure fresh batteries have been
inserted matching the correct +/- polarity orientation and are
making secure contact with the terminals.
BATTERY INSTALLATION
1. Install the batteries (see BATTERY INSTALLATION section).
2. Choose a location (see CHOOSING A LOCATION section).
3. Mount the light (see MOUNTING YOUR OUTDOOR NIGHT LIGHT
section), or simply stand the unit on any flat surface.
4. Built-in motion sensor (located below the light) automatically turns
on the light when movement in front of the light is detected. The light
remains on as long as motion continues to be detected. Please note
that there is no On/Off switch, the light can only be activated by
motion.
5. Built-in photosensor (on bottom) allows the light to only be turned on
at night or in darkness, conserving energy.
The Outdoor Night-Light will stand up by itself
and doesn’t have to be mounted unless it will be
standing in a puddle of water.
1. Take out the mounting plate by sliding it
down as shown in Battery Installation.
2. If you decide to mount it, please use the
included screws as follows: Put the flat side
against the wall and use the two screws to
install the mounting plate. If you are installing it on a very hard
surface, you may need to first drill holes for the screws.
3. The included screw anchors can be used for drywall, cement,
brick, or similar surfaces. 3. Slide down the main body of your
Outdoor Night-Light™ onto the mounting plate after the plate is
attached to the wall. Lock the mounting plate by pushing the
mounting lock towards the sensor. (It only moves a fraction of an
inch to lock).
Page 1
The selected location should not be near light sources, such as street or
porch lighting, as these may cause the Outdoor Night-Light™ to turn off
automatically. The Outdoor Night-Light™ should also be installed away
from heaters, air conditioners, barbecues, vents, and large reflective
surfaces such as swimming pools and jacuzzis, and white walls. To avoid
damage to some components, do not aim the motion sensor towards the
sun.
At night, the LED lights will remain on for about 45 seconds. The lights
gently fade so you know when they are turning off. If a movement is
detected while the lights are on, the light duration will be reset and
remain on for about another 45 seconds.
CHOOSING A LOCATION
OPERATING YOUR OUTDOOR NIGHT-LIGHT ™
Diagram 2 Diagram 1
Mounting Lock
MOUNTING YOUR OUTDOOR NIGHT-LIGHT ™