Princeton Tec REMIX PRO MPLS - Manual

REMIX TM PRO
MPLS
Operating and Maintenance
Instructions
Notice d’utilisation et d’entretien
Bedienungsanleitung
Figure 2 – Battery Replacement Remplacement des piles Einlegen der Batterien
3 1 2
Figure 1 – Switch Operation Opération de commutation Betriebsartenschalter
* Princeton Tec calculates total burn time as the time it takes for the light source to produce a
minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
* Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte
minimale Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa
der Beleuchtungsstärke des Vollmonds in einer klaren Nacht.
* Princeton Tec définit la durée totale d’éclairage comme le temps nécessaire à la source
lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la
luminosité d’une pleine lune dans un ciel nocturne dégagé.
LOW 40H HIGH 5H
DISTANCE (Meters) 16 28 28 73
press 1x = Low
press 2x = High
3 ULTRABRIGHT
LEDs
to switch between light
sources, press and hold
button (1-2 seconds)
Battery Installation – See Battery Installation Diagram
•
1 CR123 Lithium Battery
Princeton Tec cares about the environment and
recommends recycling batteries. For more information
about battery recycling, please go to:
www.batteryrecycling.com
To install the batteries, unlatch the battery door. Open the
Remix case by popping the door latch over the catch and
rotate the door open.
Install battery according to the polarity markings on the
inside of the cabinet. Observe proper battery polarity
when installing the batteries. Improper installation of the
batteries will damage the light and void the warranty.
Rotate the door to the closed position, squeeze the body
between your forefingers and thumb to snap the door
latch over the catch.
WARNING
•
Never mix fresh and used batteries.
•
Never mix different battery brands or
chemistry types.
•
Always remove drained batteries immediately.
•
Remove batteries during long periods of storage.
NOTE: Rechargeable NiCad or NiMH batteries may
result in reduced brightness due to lower nominal
voltage.
Switch Operation – See Switch Operation diagram
1. You can press the switch continuously until the light
turns off.
2. or if more than 1.6 seconds has passed (since your
last button press) the light will turn off on the next
press.
Switching from the 5mm to the Maxbright LED –
The Remix Pro has two light sources to choose from,
three Ultrabright LEDs or a Maxbright LED. Each light
source has two modes (High and Low).
To switch between light sources, press and hold the
button down until the light source switches to the desired
source. As soon as it switches release the button.
NOTE: If you keep the button pressed the light will
continue to switch back and forth between the 5mm and
Maxbright LED (on low light settings) until you release
the button.
Once you have found your desired light source, you now
can select different brightness levels. Your light will start
on “low output”. To change to “high output” you must
press the button again in less then 1.6 seconds from the
previous press. Any additional delay will cause the light to
turn off after the next button press.
One final note about the light function – If you have the
light turned on, (and more than 1.6 seconds has passed
since your last button press) and you press and hold the
button down to switch light sources, you will be in
darkness for about one second as the light sees this
press as a signal to turn the light off and switch to the
other light source simultaneously..
NVG Mounting System
To attach the MPLS Headlamp to the NVG Shroud:
1. Slide the bracket arm into the NVG Shroud adapter
plate, making sure the pull tab is above the lip of the
adapter plate and that the male grooves on the bottom of
the bracket arm are aligned inside the female grooves on
the bottom of the adapter plate.
2. Push the bracket arm securely into place, ensuring that
the pull tab audibly clicks over the lip of the NVG Shroud
adapter plate.
3. Your MPLS Headlamp should now be secured in the
NVG Shroud. You can rotate the headlamp to focus your
light source accordingly.
To remove the MPLS headlamp from the NVG Shroud:
1. Remove the NVG Mount from your helmet.
2. Push up slightly on the bottom of the light housing.
3. While pushing upward, use the tool on the provided
headstrap to press the tab of the arm bracket towards the
headlamp housing, so that it disengages from the NVG
Shroud adapter plate.
4. Slide the headlamp unit out of the NVG Shroud
adapter plate.
To attach the MPLS Headlamp to the Butterfly Mount:
1. Slide the bracket arm into the Butterfly Mount, making
sure the pull tab is above the lip of the mount and that the
male grooves on the bottom of the bracket arm are aligned
inside the female grooves on the bottom of the mount.
2. Push the bracket arm securely into place, ensuring that
the pull tab audibly clicks over the lip of the Butterfly Mount.
3. Your MPLS Headlamp should now be secured in the
Butterfly Mount. The mount can be attached to the provided
headstrap, MOLLE straps, or any 1” webbing. You can
rotate the headlamp to focus your light source accordingly.
To remove the MPLS headlamp from the Butterfly Mount:
1. Push up slightly on the bottom of the light housing.
2. While pushing upward, use the tool on the provided
headstrap to press the tab of the arm bracket towards the
headlamp housing, so that it disengages from the Butterfly
Mount.
3. Slide the headlamp unit out of the Butterfly Mount.
Troubleshooting
If the Remix Pro fails to light:
•
Check the batteries for proper installation.
•
Replace batteries if proper installation is confirmed.
•
Check the light for water contamination on the circuit
board. The light will resume normal operation once the
water is shaken or blown out and the light is left open until
completely dry. If the light has been contaminated with
salt water, flush the unit with fresh water and dry as
described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to be free
from defects in workmanship and materials under normal
use for as long as you own this product. This warranty
covers all of the component parts of the product except
batteries. This warranty does not cover deterioration due to
normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair. Princeton Tec
will repair or replace parts which are defective in
workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton Tec are
the only facilities authorized to repair the product. After (3)
unsuccessful attempts (within the warranty period) to repair
the product, you have the right to elect replacement of the
product or a refund of the purchase price less allowance for
use of the product. NO INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARE INCLUDED IN THIS WARRANTY. (Some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives you
specific legal rights, and you may also have other rights
which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
Return Policy
If your light fails to operate, follow these simple steps:
1) Check batteries. Replace if necessary.
2) Contact Princeton Tec customer service at 800-257-9080
to request an RMA number to send your light in for repair or
replacement. No warranty repairs will be accepted without
an RMA number.
3) Return the light without batteries to: Princeton Tec, 5198
Rt. 130, Bordentown, NJ 08505. Postage due and freight
collect items will not be accepted.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2011 Princeton Tec
press 1x = Low
press 2x = High
1 MAXBRIGHT
LED DISTANCE (Meters) 16 28 53 73
LOW 7H HIGH 4H
NVG Mounting System Système de montage NVG NVG-Befestigungssystem