Samsung DVD-R120-XAX - Manual (Page 27)

English - 27
Install Batteries in the Remote Control
● Open the battery cover on the back of the remote.
● Insert two AAA batteries. Make sure that the polarities
(+ and -) are aligned correctly.
● Replace the battery cover.
If the remote control does not operate properly:
● Check the polarity + - of the batteries (Dry-Cell)
● Check if the batteries are drained.
●
Check if remote sensor is blocked by obstacles.
●
Check if there is any fluorescent lighting nearby.
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
Setting the Remote Control
You can control certain functions of another
manufacturer’s TV with this remote control.
Control function buttons involve: POWER, Channel
Up/Down, Volume Up/Down, Direct Number buttons,
TV MUTE, INPUT. Depending on the manufacturer,
some buttons may not operate.
Step 6 : Preparing the Remote
Control
Controlling TVs with the Remote Control
1. Press and hold the POWER button.
2. Enter a 2-digit code by using the numerical buttons
on the remote control.
See “Controllable TV Codes”
If the code works, your TV set will be turned on or off.
If it does not respond, try other codes.
Controllable TV Codes
BRAND BUTTON
AIWA 82
ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18
BANG & OLUFSEN 57
BLAUPUNKT 71
BRANDT 73
BRIONVEGA 57
CGE 52
CONTINENTAL EDISON 75
DAEWOO 19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34
EMERSON 64
FERGUSON 73
FINLUX 06, 49, 57
FORMENTI 57
FUJITSU 84
GRADIENTE 70
GRUNDIG 49, 52, 71
HITACHI 60, 72, 73, 75
IMPERIAL 52
JVC 61, 79
LG 06, 19, 20, 21, 22, 78
LOEWE 06, 69
LOEWE OPTA 06, 57
MAGNAVOX 40
METZ 57
MITSUBISHI 06, 48, 62, 65
MIVAR 52, 77
NEC 83
NEWSAN 68
NOBLEX 66
NOKIA 74
NORDMENDE 72, 73, 75
PANASONIC 53, 54, 74, 75
PHILIPS 06, 55, 56, 57
PHONOLA 06, 56, 57
PIONEER 58, 59, 73, 74
RADIOLA 06, 56
RADIOMARELLI 57
RCA 45, 46
REX 74
SABA 57, 72, 73, 74, 75
SALORA 74
SAMSUNG 01,02,03,04,05,06,07,08,09
SANYO 41, 42, 43, 44, 48
SCHNEIDER 06
SELECO 74
After all connections are complete, plug the power cord
in the wall outlet.
“Auto” appears in the panel display. This means
that the current time is being set automatically
(Auto Program) through the antenna under
connection and also the channel is being set.
The setup may take a few minutes.
When the DVD Recorder operates normally, the current
time is automatically set and displayed in the front
panel display.
Step 5 : Connecting the Power
Cord
■ After the current time is set automatically,
the recorder will perform Auto Channel
Memory for about 3 minutes. If power is
on, while Auto Channel Memory is in
process, Auto Channel Memory will stop.
In this case, do Auto Channel Memory
from MENU(see pages 31~32).
NOTE
C
onnecting & Setting UP
AK68-00683A-0v(14~35) 2005.9.28 5:31 AM Page 27