Alpine CDA-9853 - Manual (Page 16)

15
-EN
Sound Setting
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat
1
Press the Rotary encoder (MODE) repeatedly to
choose the desired mode.
Each press changes the modes as follows:
SUBWOOFER* 1 → BALANCE → FADER → DEFEAT →
VOLUME → SUBWOOFER* 1
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Press g or f after selecting the Subwoofer mode,
and the subwoofer output phase is switched NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
• If the Rotary encoder (MODE) is not pressed within 5 seconds
after selecting the BALANCE, FADER, DEFEAT or SUBWOOFER
mode, the unit automatically returns to normal mode.
• If you set the 2WAY/3WAY switch (pages 45 to 47) to 3WAY, you
cannot adjust the FADER mode.
* 1 When the subwoofer mode is set to OFF, its level and phase cannot
be adjusted.
2
Turn the Rotary encoder (MODE) until the
desired sound is obtained in each mode.
By setting Defeat ON, previously adjusted settings of EQ
will return to the factory defaults and MX is turned off.
• Depending on the connected devices, some functions and display
indications do not work.
Equalizer Presets
9 typical equalizer settings are preset at the factory for a variety of
musical source material.
1
Press MENU.
2
Select the Factory’s EQ mode by sliding your finger
on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Factory’s EQ
mode.
3
Select the desired equalizer characteristic by
sliding your finger on the GlideTouch bar to the
left or right.
• By selecting USER’S 1 to 6, you can recall the stored preset
number in “Adjusting and Storing the Graphic Equalizer Curve.”
(page 16) or “Adjusting and Storing the Parametric Equalizer
Curve” (page 16) .
4
Press and hold MENU for at least 2 seconds to
return to normal mode.
• This function is inoperable when DEFEAT is set to ON (this page).
• If MENU is pressed while adjusting or setting the itmes in the
MENU mode, the unit will return to the previous selection secreen.
• By pressing the GlideTouch bar under RETURN in the MENU
mode, the unit will return to the normal mode.
Setting User's EQ mode
This setting gives you a choice of 5-band parametric, or 7-band
graphic equalizer.
1
Press MENU.
2
Select SETUP by sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under SETUP.
The main SETUP menu is displayed.
3
Select AUDIO by sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under AUDIO.
The AUDIO SETUP menu is displayed.
4
Select EQ MODE by sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under EQ MODE.
5
Select EQ Type by sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under PEQ or GEQ.
PEQ : 5-band parametric EQ (initial setting)
GEQ : 7-band graphic EQ
6
Press and hold MENU for at least 2 seconds to
return to normal mode.
• If MENU is pressed while adjusting or setting the itmes in the
MENU mode, the unit will return to the previous selection secreen.
• By pressing the GlideTouch bar under RETURN in the MENU
mode, the unit will return to the normal mode.
BAND
SOURCE/
POWER
g f FUNC. GlideTouch bar
Rotary encoder (MODE)
MENU