Sony ZS-E5AQUA - Manual (Page 2)

ZS-E5_4-138-358-11(1)_U2
Basic Operations
  have a tactile dot.
Precautions
Discs that this unit CAN play
• Audio CD
• CD-R/CD-RW (CD-DA*)
* CD-DA is the abbreviation for Compact Disc Digital
Audio. It is a recording standard used for Audio CDs.
Discs that this unit CANNOT play
• CD-R/CD-RW other than those recorded in music CD
format
• CD-R/CD-RW of poor recording quality, CD-R/CD-
RW that has scratches or are dirty, or CD-R/CD-RW
recorded with an incompatible recording device
• CD-R/CD-RW which is finalized incorrectly
Notes on discs
• Before playing, clean the CD with
a cleaning cloth. Wipe the CD
from the center out. If there is a
scratch, dirt or fingerprints on the
CD, it may cause tracking errors.
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
• Do not expose the CD to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in
direct sunlight, as there can be a considerable rise in
temperature inside the car.
• Do not stick paper or stickers on the CD, nor scratch
the surface of the CD.
• After playing, store the CD in its case.
On safety
• As the laser beam used in the CD player section is
harmful to the eyes, do not attempt to disassemble the
casing. Refer servicing to qualified personnel only.
• Should any solid object or liquid fall into the player,
unplug the player, and have it checked by qualified
personnel before operating it any further.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this player. Attempting to do
so may damage the player. Do not use such discs.
On power sources
• For AC operation, use the supplied AC power cord; do
not use any other type.
• Unplug the player from the wall outlet when it is not to
be used for an extended period of time.
• When the batteries are not to be used, remove them to
avoid damage that can be caused by battery leakage or
corrosion.
On placement
• Do not leave the player in a location near heat sources,
in a place subject to direct sunlight, excessive dust, or
mechanical shock, or in a car subject to the direct rays
of the sun.
• Do not place the player on an inclined or unstable
place.
• Do not place anything within 10 mm of the side of the
cabinet. The ventilation holes must be unobstructed for
the player to operate properly and prolong the life of its
components.
• Since a strong magnet is used for the speakers, keep
personal credit cards using magnetic coding or spring-
wound watches away from the player to prevent
possible damage from the magnet.
On operation
• If the player is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lens inside the CD player section.
Should this occur, the player will not operate properly.
In this case, remove the CD and wait about an hour for
the moisture to evaporate.
Cleaning the cabinet
• Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder, or
solvent, such as alcohol or benzine.
If you have any questions or problems concerning your
player, please consult your nearest Sony dealer.
Troubleshooting
General
The power is not on.
• Connect the AC power cord to the wall outlet securely.
• Make sure the batteries are inserted correctly.
• Replace all the batteries with new ones if they are weak.
Noise is heard.
• Someone is using a portable telephone or other
equipment that emits radio waves near the player.
 Move the portable telephone, etc., away from the
player.
CD player
The CD does not play or “– –” is displayed even
when a CD is in place.
• Place the CD with the label surface up.
• Clean the CD.
• Take out the CD and leave the CD compartment open
for about an hour to dry moisture condensation.
• The CD-R/CD-RW is blank.
• There is a problem with the quality of the CD-R/
CD-RW, recording device or application software.
• Replace all the batteries with new ones if they are weak.
The sound drops out.
• Reduce the volume.
• Clean the CD, or replace it if the CD is badly damaged.
• Place the player in a location free from vibration.
• Clean the lens with a commercially available blower.
• The sound may drop out or noise may be heard when
using poor quality CD-Rs/CD-RWs, or if there is a
problem with the recording device or application
software.
Radio
Reception is poor.
• Reorient the
antenna to
improve FM
reception.
• Reorient the player
itself to improve
AM reception.
The audio is weak or has poor quality.
• Replace all the batteries with new ones if they are weak.
• Move the player away from the TV.
The picture of your TV becomes unstable.
• If you are listening to an FM program near the TV with
an indoor antenna, move the player away from the TV.
After trying the remedies, if you still have problems,
unplug the AC power cord or remove all the batteries.
After all the indications in the display disappear, plug
the AC power cord in or insert the batteries again. If the
problem persists, please consult your nearest Sony
dealer.
Playing a CD
1 Pull PULL OPEN  to open the CD compartment lid
and place a disc on the pivot in the center of the
tray.
2 Close the CD compartment lid.
3 Set the function selector  to CD.
OPR/BATT indicator  turns on and total track
number appears in the display after “– –” blinks.
4 Press   .
“01” appears in the display to indicate that track 1 of
the CD is playing. The unit plays all the tracks once.
To Press
Pause playback  
Stop playback  
Go to the next
track
 
Go back to the
previous track
 
Locate a point
while listening to
the sound
 (forward) or  (backward)
 while playing and hold it until
you find the point.
Remove the CD PULL OPEN 
To remove the CD
Remove the CD as illustrated below.
Listening to the radio
1 Set the function selector  to RADIO.
OPR/BATT indicator  turns on.
2 Select a desired band using  .
3 Tune in to the station using TUNE  .
If FM stereo reception is too weak, the reception
switches to monaural.
Connecting optional components
You can enjoy the sound from an optional component
such as a portable digital music player through the
speakers of this unit. Be sure to turn off the power of
each component before making any connections. For
details, refer to the instruction manual of the component
to be connected.
1 Connect the AUDIO IN jack  on the back of the
unit to the line output jack of a portable digital
music player or other component using an audio
connecting cable (not supplied).
2 Turn the unit and the connected component on.
3 Set the function selector  to AUDIO IN and start
playback of the connected component.
The OPR/BATT indicator
 turns on and the sound
from the connected component is output from the
speakers of this unit.
To connect the unit to a TV or VCR, use an extension
cable (not supplied) with a stereo-mini jack on one
end and two phono plugs on the other end.