Sony CDX-M850MP User Manual

Fm / am compact disc player, 2a b, Cdx-m850mp

Advertising
background image

BUS CONTROL IN

BUS AUDIO IN

Source selector*
Sélecteur de source*
Selector de fuente*

XA-C30

* not supplied

non fourni
no suministrado

© 2003 Sony Corporation

Printed in Korea

3-251-115-11

(1)

Cautions

• This unit is designed for negative ground 12 V DC

operation only.

• Do not get the wires under a screw, or caught in

moving parts (e.g. seat railing).

• Before making connections, turn the car ignition

off to avoid short circuits.

• Connect the yellow and red power input leads

only after all other leads have been connected.

Run all ground wires to a common ground

point.

• Be sure to insulate any loose unconnected wires

with electrical tape for safety.

• The use of optical instruments with this product

will increase eye hazard.

Notes on the power supply cord (yellow)
• When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

• When no car circuits are rated high enough,

connect the unit directly to the battery.

Parts Iist (1)

• The numbers in the list are keyed to those in the

instructions.

• The bracket 1 is attached to the unit before

shipping. Before mounting the unit, use the
release keys 5 to remove the bracket 1 from the
unit. For details, see “Removing the bracket (4)”
on the reverse side of the sheet.

Keep the release keys 5 for future use as they

are also necessary if you remove the unit from
your car.

Caution

Handle the bracket 1 carefully to avoid injuring
your fingers.

Note
Before installing, make sure that the catches on both
sides of the bracket
1 are bent inwards 2 mm (

3

/

32

in). If

the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.

Connection example (2)

Notes (2-A)
• Be sure to connect the ground cord before connecting

the amplifier.

• If you connect an optional power amplifier and do not

use the built-in amplifier, the beep sound will be
deactivated.

Tip (2-B-

)

For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.

Installation/Connections

Installation/Connexions

Instalación/Conexiones

FM/AM
Compact Disc
Player

Connection diagram (3)

1

To a metal surface of the car
First connect the black ground lead, then connect
the orange/white striped, yellow, and red power
input leads.

2

To the power antenna control lead or power
supply lead of antenna booster amplifier

Notes
• It is not necessary to connect this lead if there is no

power antenna or antenna booster, or with a
manually-operated telescopic antenna.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control and
power supply leads.”

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the interface cable of a car telephone

5

To a car’s illumination signal
Be sure to connect the black ground lead to a metal
surface of the car first.

6

To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch

Notes
• If there is no accessory position, connect to the +12

V power (battery) terminal which is energized at
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.

• When your car has a built-in FM/AM antenna in

the rear/side glass, see “Notes on the control and
power supply leads.”

7

To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a metal
surface of the car first.

Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V

DC when you turn on the tuner.

• When your car has built-in FM/AM antenna in the rear/

side glass, connect the power antenna control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.

• A power antenna without relay box cannot be used

with this unit.

Memory hold connection
When the yellow power input lead is connected, power
will always be supplied to the memory circuit even when
the ignition key is turned off.

Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and

with adequate power handling capacities to avoid its
damage.

• Do not connect the speaker terminals to the car

chassis, or connect the terminals of the right speakers
with those of the left speaker.

• Do not connect the ground lead of this unit to the

negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active

speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker

wires installed in your car if the unit shares a common
negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker cords to each other.

Note on connection
If speaker and amplifier are not connected correctly,
“Failure” appears in the display. In this case, make sure
the speaker and amplifier are connected correctly.

2

A

B

AUDIO OUT

FRONT

AUDIO OUT

REAR

BUS AUDIO IN

BUS CONTROL IN

1

3

2

Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Equipo utilizado en las ilustraciones (no suministrado)

Rear speaker
Haut-parleur arrière
Altavoz posterior

Front speaker
Haut-parleur avant
Altavoz frontal

1

CD/MD changer
Changeur de CD/MD
Cambiador de CD/MD

Power amplifier
Amplificateur de puissance
Amplificador de potencia

Ч

4

5

Ч

2

4

Active subwoofer
Caisson de graves actif
Subwoofer activo

SUB OUT (MONO)

CDX-M850MP

Catch

1

Rotary commander RM-X4S
Satellite de commande RM-X4S
Mando rotativo RM-X4S

Advertising