CatEye HL-EL820RC [Double Shot Pro] - Manual

1 2 4 5
6
7
8 9
0
3
HL-EL820RC
5
LOCK
Ring
8
3
7
2
1
0
2
1 2
4 3
4
1
3
0
9
3
9
2
Pat. and Design Pat. Pending Copyright©2006 CATEYE Co., Ltd. ENG
To Top tube
Installing Bracket
Attach the helmet mount to the helmet.
1. Securely fasten the helmet mount to the front part of the helmet, wrapping the velcro
strap through the air vents on the helmet.
Attaching/removing the Light unit
1. Mount the light unit onto the helmet mount.
2. Secure the cable on the rear of the helmet using the spare cable strap.
Put on the helmet and adjust the angle of the beam. To remove the
light unit, pull the light unit forward while pressing the button on the base of the light unit.
CAUTION!: Make sure the light unit is cool to the touch before removing it.
Connecting the extension cord
Connect the extension cable.
1. Connect the extension cable between the light unit and the battery unit as shown in
the figure.
CAUTION!: Slide the ring of the plug forward and turn it to lock the plug. It must
remain locked when in use.
Installing Battery unit
When putting the battery unit in the strap or the pocket, attach the battery clip to the
battery unit.
1. Remove the battery rubber pad of the battery unit.
2. Secure the battery unit with the clip strap.
NOTE: Secure the clip belt by wrapping it around the center of the batteries.
3. Secure the clip by tucking it in the pocket or the bag.
CAUTION!: Arrange the cable so that it does not interfere with riding. Do not bend
the cable strongly because the wire inside the cable may break.
Installing Bracket
Attach the bracket to the handlebar.
1. Wrap the bracket strap around the handlebar, and put it in the dial.
2. Securely tighten the strap by turning the dial.
CAUTION!: • Make sure to tighten the dial by hand. If you tighten it too hard with
a tool, the screw threads may be stripped.
• When the angle adjustment on the right and left sides is loose,
tighten the screw.
3. Cut off the excess bracket strap extending from the dial.
CAUTION!: Round off the cut edge of the bracket strap to prevent injury.
Attaching/removing the Light unit
1. Slide the light unit into the bracket as shown.
To remove unit after use, pull it out while pressing the button on the bracket.
CAUTION!: Make sure the light unit is cool to the touch before removing it.
Installing Battery unit
Mount the battery unit onto the bicycle frame as shown.
1. Put the battery unit through the loop of the fixing strap.
CAUTION!: Check that the position of the fixing strap is within the installation
range of the battery rubber pad of the battery unit.
2. Secure the battery unit by wrapping the fixing strap around the top tube so that the
battery rubber pad comes into contact with the frame.
CAUTION!: Do not wrap the fixing strap from above the cables.
Doing so is dangerous because it may interfere with braking and gear
shifting.
Connecting and Securing cables
Connect the light unit with the battery as shown.
1. Connect the plug of the light unit to the battery unit as shown in the figure.
CAUTION!: Slide the plug ring forward and then turn it to lock. Make sure that the
ring is locked before use.
2. Fix the cables to your frame and/or stem to keep them secured.
CAUTION!: • Pay attention to the arrangement of the cable so that it does not
interfere with the handling of the bicycle. Do not secure the cable
at an acute angle because the wire inside the cable may break.
• Adjust the beam angle according to “How to Adjust the Beam Angle”
in this manual.
Bracket strap
Button
Clip strap
MOUNTING THE LIGHT UNIT ON A HELMET
Bracket strap
Dial
Bracket rubber pad
Button
Screw
HOW TO MOUNT TO A BICYCLE
1
1
2
3
4
LOCK
Ring
2
3
4
INTRODUCTION
Before using the light, be sure to thoroughly read this instruction
manual and accompanying "Lithium-ion Batteries".
This product combines high-power LEDs, Cateye Opticube lens technology, and com-
pact lithium ion battery to produce a super bright, extremely durable high-performance
light. Mounts on both helmet and handlebar.
1 Light unit
2 Battery unit (lithium-ion batteries)
3 Battery rubber pad
4 Battery charger 5 Bracket (For the helmet)
6 Bracket H34 (For the handlebar)
7 Battery clip
8 Extension cable 9 Fixing strap
0 Cable straps (x 2)
Installation range
Gear & Brake Cables
Top tube