AMX Signature Series NetLinx Integrated Controller NI-3101-SIG User Manual
Ni-3101-sig
Advertising
Table of contents
Document Outline
- NI-3101-SIG Signature Series NetLinx Integrated Controller Operation/Reference Guide
- Introduction
- Installation and Upgrading
- Connections and Wiring
- Setting the Configuration DIP Switch for the Configuration Port
- Configuration Port Connections and Wiring
- Modes and Front Panel LED Blink Patterns
- Port Assignments and Functionality
- AXlink Port and LED
- Wiring Guidelines
- DB9 Device Port: Connections and Wiring
- Relay Port: Connections and Wiring
- Input/Output (I/O) Port: Connections and Wiring
- IR/Serial Port: Connections and Wiring
- LAN (Ethernet/RJ-45 Port): Connections and Wiring
- Replacing the Timekeeper Battery
- Configuration and Firmware Update
- Overview
- Communicating with the Master via the Program Port
- Setting the System Value
- Changing the Device Address of a NetLinx Device
- Using the ID Button to Change the Controller’s Device Value
- Resetting the Factory Default System and Device Values
- Obtaining the Master’s IP Address (using DHCP)
- Assigning a Static IP to the NetLinx Master
- Communicating with the NI Device via an IP
- Verifying the current version of NetLinx Master Firmware
- Upgrading the On-board Master Firmware via an IP
- Upgrading the NI Controller Firmware via IP
- NetLinx Security within the Web Server
- NetLinx Security Terms
- Accessing an Unsecured Master via an HTTP Address
- Browser Application Frames
- Default Security Configuration
- Master Firmware Security Access Parameters
- Web Control
- Security Features
- Security - System Level Security page
- Setting the system security options for a NetLinx Master
- ICSP Authentication
- Security - Group Level Security page
- Adding a new Group
- Modifying the properties of an existing Group
- Deleting an existing Group
- Security - User Level Security page
- Adding a new User
- Modifying the properties of an existing User
- Deleting an existing User
- System Settings
- Manage System - System Menu Buttons
- Setting the Master’s Port Configurations
- SSL Server Certificate Creation Procedures
- Common Steps for Requesting a Certificate from a CA
- Manage System - Device Menu Buttons
- System Settings - Manage License
- System Settings - Manage NetLinx Devices
- System Settings - Manage Other Devices - Dynamic Device Discovery Pages
- Manage Other Devices - Manage Device Bindings
- Configuring application-defined devices
- What are Application Devices and their association status?
- Manage Other Devices Menu - Viewing Discovered Devices
- Manage Other Devices Menu - Creating a new User-Defined Device
- How do I write a program that uses Dynamic Device Discovery
- How do I configure a Run-time installation
- Accessing an SSL-Enabled Master via an IP Address
- What to do when a Certificate Expires
- NetLinx Security with a Terminal Connection
- Overview
- NetLinx Security Features
- Initial Setup via a Terminal Connection
- Accessing the Security configuration options
- Option 1 - Set system security options for NetLinx Master (Security Options Menu)
- Option 2 - Display system security options for NetLinx Master
- Option 3 - Add user
- Option 4 - Edit User
- Edit User Menu
- Access Rights Menu
- Option 5 - Delete user
- Option 6 - Show the list of authorized users
- Option 7 - Add Group
- Edit Group Menu
- Edit Group menu: Delete directory association
- Edit Group menu: List directory associations
- Edit Group menu: Change Access Rights
- Edit Group menu: Display Access Rights
- Option 8 - Edit Group
- Option 9 - Delete Group
- Option 10 - Show List of Authorized Groups
- Option 11 - Set Telnet Timeout in seconds
- Option 12 - Display Telnet Timeout in seconds
- Option 13 - Make changes permanent by saving to flash
- Main Security Menu
- Default Security Configuration
- Logging Into a Session
- Logout
- Programming
- Converting Axcess Code to NetLinx Code
- Master Send_Commands
- Master IP Local Port Send_Commands
- Using the ID Button
- Configuration Port Commands
- ESC Pass Codes
- Notes on Specific Telnet/Terminal Clients
- LED Disable/Enable Send_Commands
- RS232/422/485 Ports Channels
- RS-232/422/485 Send_Commands
- RS-232/422/485 Send_String Escape Sequences
- IR / Serial Ports Channels
- IR/Serial Send_Commands
- Input/Output Send_Commands
- Troubleshooting