Aiwa BMZ-K1 - Manual (Page 21)

21
En
REFERENCE
Frequently Asked Questions for USB
function
Q. Compared to the volume of the main unit CD player, the
volume of the PC connected by USB is too small.
A. Adjust the volume setting on the PC. Open “Multimedia”
or “Sound and Multimedia” on the Control Panel, and
adjust “Sound volume” and “WAVE balance” in the Audio
tab.
Q. Winamp starts, but the display on the main unit shows
only “USB”.
A. The Winamp3 BMZ Plug-in is not installed. Install the plug-
in.
Q. Winamp does not respond when I press buttons like c
and s on the main unit.
A. The BMZ USB Driver may not be installed, or the Winamp3
BMZ Plug-in may not be installed, or another plug-in may
be intefering with the BMZ Plug-in. Click the Add and Delete
Applications icon in the Control Panel to delete the BMZ
USB Driver and Winamp3, and install them again.
Q. The main unit does not play sound from the PC.
A. The PC many not be connected with a USB cable, or
FUNCTION may not be set to USB. Or, the PC speakers
may be muted, or audio output may be set to a different
device. Check under “Multimedia” or “Sound and
Multimedia” on the Control Panel.
Q. I can’t install the USB driver in Windows98.
A. The USB driver supports only Windows XP/2000/Me/
Second Edition. It cannot be installed on Windows 98
except for Windows 98 Second Edition.
Q. When Winamp is playing, the sound fades out from one
song and into the next song.
A. The Cross Fade button in Winamp is on. Turn the button
off.
Q. Winamp3 becomes unplayable suddenly.
A. Use latest Microsoft DirectX
® after downloading from
Microsoft web site.
Q. PLAYLIST EDITOR does not necessarily show the same
play list that is currently selected by the Winamp3.
A. During playback, the correct play list is shown.
Q. Winamp3 does not respond when I change setting of the
USB port.
A. Install the software in the supplied BMZ USB Driver CD
again.
Q. PLAY LIST becomes unplayable suddenly.
A. Right-click the PLAY LIST EDITOR window.
Q. The spectrum analyser of this unit does not respond or
playback cannot stop when close Winamp3 during CD
playback from CD-ROM drive on PC.
A. The PC's CD-ROM drive may sometimes be incapable of
performing intended operations. In this case, restart the
main unit and the Winamp3. And if you playback an audio-
CD, we recommend to use the disc player of this unit.
Q. How can I get information of Winamp?
A. Refer to web site of Winamp (http://www.winamp.com).
Care and maintenance
Occasional care and maintenance of the unit and the software
are needed to optimize the performance of your unit.
To clean the cabinet
Use a soft and dry cloth. If the unit surfaces are extremely
dirty, use a soft cloth lightly moistened with mild detergent
solution. Do not use strong solvents such as alcohol, benzine
or thinner.
Care of CDs
When a CD becomes dirty, wipe it from the centre out with a
cleaning cloth. Please do not use solvents. After playing a
CD, store it in its case. Do not expose a CD to direct sunlight
or heat sources.
Troubleshooting
If your unit fails to perform properly, check the following guide
and the relevant sections of the Operating Instructions.
First check that the AC power cord and the speakers are
connected correctly and firmly.
Should any problem persist, consult your nearest Aiwa dealer.
General
There is no sound
•Are the speakers and AC power cord connected properly?
•Turn VOLUME clockwise and hold.
•Check the volume level of Winamp3 in your computer.
•The headphones are connected.
•Insert only the stripped portion on the speaker cord into the
SPEAKERS terminal. Inserting the vinyl portion of the
speaker cord will obstruct the speaker connections.