Pioneer DJM-800 - Manual (Page 13)

13
<DRB1392>
En
English
7 Use the CROSS FADER curve switch to select the cross
fader curve response.
¶ At the left setting, the curve produces a rapid signal rise. (As
soon as the cross fader lever leaves the [A] side, the [B] channel
sound is produced.)
¶ At the right setting, the curve operates to produce an even,
neutral rise throughout the cross fader’s movement.
¶ At the middle setting, an intermediate curve is produced,
midway between the two curves noted above.
¶ This setting produces equal curve effects for both sides A and
B.
FADER START FUNCTION
By connecting the optional Pioneer DJ CD Player control cable, the
channel fader and cross fader can be used to start CD playback.
When the mixer’s channel fader lever or cross fader lever are moved,
the CD player is released from the pause mode and automatically –
and instantly – begins playback of the selected track. Also, when the
fader lever is returned to its original position, the CD player returns to
its cue point (back cue), thus allowing “sampler” type play.
Cross fader start play and back cue play
When the CD player assigned to cross fader channel A is set to
standby at a cue point, moving the cross fader lever from the right (B)
side toward the left (A) side automatically starts play on the channel
A CD player.
When the cross fader lever reaches the left (A) side, the CD player
assigned to channel B goes to back cue (returns to cue point). Also,
when the CD player assigned to channel B is set to standby at a cue
point, moving the cross fader lever from the left (A) side to the right
(B) side automatically starts playback on the channel B CD player.
When the cross fader lever reaches the right (B) side, the CD player
assigned to channel A goes to back cue (returns to cue point).
* The back cue is performed even if the input selector switch is not
set to [CD/DIGITAL] or [LINE/DIGITAL].
[Using the Channel Fader to Start Playback]
1
2
4
FADER
START
1, 2, 3, 4
1. Press the FADER START button for the channel (1 to 4)
connected to the CD player you wish to control.
¶ The button for the selected channel lights.
2. Set the channel fader lever to “0”.
3. Set the CD player to the desired cue point, and engage cue
point standby.
¶ If a cue point has already been set, it is not necessary to set the
CD player to standby at the cue point.
4. At the instant you wish to start playback, move the
channel fader lever.
¶ CD player begins playback.
¶ After playback has begun, if the channel fader lever is returned
to the [0] position, the CD player returns to the cue point and re-
enters standby mode (back cue).
* Playback control is possible with the channel fader only with the
CROSS FADER ASSIGN switch is set to [THRU].
[Using the Cross Fader to Start Playback]
1. Press the FADER START button for the channel (1 to 4)
connected to the CD player you wish to control.
¶ The button for the selected channel lights.
2. Set the CROSS FADER ASSIGN switch for the selected
channel to [A] or [B].
¶ Select [A] to assign to cross fader channel A (left side).
¶ Select [B] to assign to cross fader channel B (right side).
3. Move the cross fader lever to the full opposite side away
from the CD player you wish to start.
4. Set the CD player to the desired cue point, and engage cue
point standby.
¶ If a cue point has already been set, it is not necessary to set the
CD player to standby at the cue point.
5. At the instant you wish to start playback, move the cross
fader lever.
¶ CD player begins playback.
¶ After playback has begun, if the cross fader lever is moved fully
to the opposite side, the CD player assigned to the opposite
side channel will return to the cue point and enter standby
mode (back cue).
Note:
The fader start function will not be enabled if digital connections are
used alone; to use the fader start function, be sure to connect the CD
player’s analog connectors as well.
1
2
3 5
FADER
START
1, 2, 3, 4
CROSS
FADER
ASSIGN
A / THRU / B
MIXER OPERATIONS (FADER START FUNCTION)