Pioneer KEH-P2033R User Manual

Inst alla tion manual manuel d’inst alla tion, Instalación <español, Installation <english

Advertising
background image

Nota:

Antes de finalmente instalar la unidad, conecte el
cableado temporalmente y asegúrese de que todo
esté conectado correctamente y que la unidad y
el sistema funcionan debidamente.

Utilice sólo las piezas que se incluyen con esta
unidad para asegurar la instalación adecuada. El
uso de piezas no autorizadas podría causar fallos
de funcionamiento.

Consulte con su distribuidor si la instalación
requiere del taladro de orificios u otras modifica-
ciones del vehículo.

Instale la unidad donde no alcance el espacio del
conductor, y donde no pueda dañar a los
pasajeros si sucediera un paro repentino, como
una detención de emergencia.

Si el ángulo de la instalación excede los 30° del
lado horizontal, la unidad podría no brindar su
óptimo funcionamiento. (Fig. 1)

Instalación con tope de goma
(Fig. 2)

1. Tablero de instrumentos
2. Soporte

Después de insertar el soporte en la tabla de
mandos, luego seleccione las orejetas apropiadas
según el grosor del material de la tabla de man-
dos y dóblelos.
(Instale lo más firme posible usando las lengüe-
tas superior e inferior. Para fijar, doble las
lengüetas 90 grados.)

3. Tope de goma
4. Tornillo

Quitado de la unidad (Fig. 3)

5. Inserte las herramientas de extracción suminis-

tradas en la unidad, como se indica en la figura,
hasta que se enganchen en su positión.
Tire de la unidad mientras mantiene las her-
ramientas presionadas contra los lados de la
unidad.

Sobre los tornillos de fijación del
panel delantero (Fig. 4)

6. Tornillos de fijación

Si no desea utilizar la función de extracción y
colocación del panel delantero, utilice los tornil-
los de fijación suministrados y fije el panel
delantero a esta unidad.

Instalación

<ESPAÑOL>

Note:

Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.

Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.

Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.

Install the unit where it does not get in the dri-
ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.

If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 1)

Installation with the rubber bush
(Fig. 2)

1. Dashboard
2. Holder

After inserting the holder into the dashboard,
then select the appropriate tabs according to the
thickness of the dashboard material and bend
them.
(Install as firmly as possible using the top and
bottom tabs. To secure, bend the tabs 90
degrees.)

3. Rubber bush
4. Screw

Removing the Unit (Fig. 3)

5. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.
Keeping the keys pressed against the sides of the
unit, pull the unit out.

About the fixing screws for the
front panel (Fig. 4)

6. Fixing screw

If you do not operate the Removing and
Attaching the Front Panel Function, use the sup-
plied fixing screws and fix the front panel to this
unit.

Installation

<ENGLISH>

30˚

5

Fig. 1

Abb. 1

Afb. 1

Fig. 2

Abb. 2

Afb. 2

1

2

3

4

<KSNZX/02H00000>

KEH-P2033R
KEH-P2030R

Printed in Malaysia
Imprimé en Malaisie

<CZR2961-A> EW

This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen kabelfarben.
Le code de couleur des câbles utilisé pour ce produit
est nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.

Fig. 3

Abb. 3

Afb. 3

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

Fig. 4

Abb. 4

Afb. 4

6

CZR2961-A 02.8.6 10:07 AM Page 1

Advertising
This manual is related to the following products: