Pioneer CDJ-200 - Manual (Page 29)

OTHER (TROUBLESHOOTING)
29
<DRB1376>
En
English
Fran
ç
ais
TROUBLESHOOTING
Incorrect operations can be mistaken as malfunctions. If you believe the unit is not operating correctly, consult the chart below.
Sometimes incorrect operation may be due to a malfunction in another component. If the problem is not fixed, check the other
components used with the player. If the problem still persists, contact your nearest Pioneer authorized service center or dealer for
service.
÷ Static electricity and other external effects may cause this unit to malfunction. In this case, set the POWER switch to OFF, then
switch it on again after the disc has come to a complete stop.
÷ This unit cannot playback unfinalized (partial discs) CD-R or CD-RW discs.
÷ This component is designed to play 12 cm discs and 8 cm discs with a commercially available adaptor, eccentrically shaped
discs cannot be played since damage or malfunction may result.
÷ The BPM value measured by the CDJ-200 may differ from the BPM value recorded on a CD or from our DJ mixer, but this
difference is a result of differences in the BPM value measurement method; not a result of a fault with the player.
÷ When playing CD-R/RW discs, the performance rate may drop due to quality of the recorded data.
Symptom
Disc doesn’t eject even when EJECT
button (
0) is pressed.
Play doesn’t commence even when
the disc is inserted.
Playback immediately stops when
started. During playback, the player
pauses or stops.
No sound is audible.
Cannot playback MP3s.
Sound is distorted, noise is output.
With certain discs, loud noise is
produced or play stops.
When the auto cue function is set
ON, track search is not finished.
Back cue function cannot be carried
out even though the CUE button is
pressed in playback mode.
Pressing the OUT/OUT ADJUST
button does not start loop play.
Cannot search MP3s.
The picture of the TV screen is
fluctuated or FM broadcast is
interfered with noise.
The disc is not rotating when power
is ON.
Cause
÷ Power plug is disconnected from outlet.
÷ The auto cue function is set to on.
÷ Smudges on the disc, etc.
÷ Output cables are connected incorrectly or
are loose.
÷ Incorrect operation of DJ mixer.
÷ Pin plugs and/or amplifier terminals are
dirty.
÷ Player is in pause mode.
÷ The files are in the wrong format.
÷ Incorrect connections.
÷ Pin plugs and/or amplifier terminals are
dirty.
÷ Interference is being picked up from a TV
set.
÷ Disc has a bad scratch or warp.
÷ Disc is extremely dirty.
÷ If the sound muted portion between
selections is long, searching time will be
long.
÷ The cue point is not set yet.
÷ The cue point is set to an MP3 file in a
different folder.
÷ No cue points (loop-in points) have been set.
÷ The OUT/OUT ADJUST button was
pressed during the playback of an MP3 file
other than the one with the cue point (loop-
in point) set.
÷ Attempted to search (fast-forward/fast-
reverse) MP3s into a different folder.
÷ Interference is being picked up from the CD
player.
÷ The disc rotation stops automatically if no
operation has been performed for 100
minutes or more in pause mode.
÷ When the last track on the disc is over the
disc stops rotating.
Remedy
÷ Connect plug to wall outlet.
÷ Press the AUTO CUE button to turn off the
Auto Cue function.
÷ Clean the smudges from the disc and then
play it again.
÷ Recheck connections. Refer to installation
instructions.
÷ Check the settings of the DJ mixer switches
and sound volume controls.
÷ Clean away dirt.
÷ Press the PLAY/PAUSE button (6).
÷ Refer to P.6 “PLAYING MP3 FILES.”
÷ Connect to audio mixer's LINE INPUT termi-
nals. (Do not connect to MIC terminals.)
÷ Clean away dirt.
÷ Switch OFF TV set, move player away from TV
set or plug the player into a separate outlet.
÷ Replace disc.
÷ Clean disc.
÷ Press the AUTO CUE button to turn off the
Auto Cue function.
÷ Set the cue point. (See page 24.)
÷ During playback of MP3s, back cue is possible
only within the same folder.
÷ Set a cue point.
÷ During playback of MP3s, looping is possible
only within the same track that has a cue point
(loop-in point) set.
÷ Searching with MP3s are only possible within
the same folder.
÷ Turn off POWER switch of the player, or move
the player away from the TV or tuner.
÷ Playback can be started from the first track by
pressing the PLAY/PAUSE button ( 6). Press
the EJECT button ( 0) to eject the disc.