Conexión de las unidades, Español, Connecting the units <english – Pioneer DEH-P6700MP User Manual

Page 6: Diagrama de conexión (fig. 12), Connection diagram (fig. 12)

Advertising
background image

Nota:

Esta unidad es para vehículos con batería de 12
voltios y con conexión a tierra. Antes de instalar la
unidad en un vehículo recreativo, camioneta, o
autobús, revise el voltaje de la batería.

Para evitar cortocircuitos en el sistema eléctrico,
asegúrese de desconectar el cable de la batería ≠
antes de comenzar con la instalación.

Consulte con el manual del usuario para los
detalles sobre la conexión de la alimentación de
amperios y de otras unidades, luego haga las
conexiones correctamente.

Asegure el cableado con abrazaderas de cables o
con cinta adhesiva. Para proteger el cableado,
envuélvalo con cinta adhesiva donde éstos se
apoyan sobre las piezas de metal.

Coloque y asegure todo el cableado de tal manera
que no toque las piezas en movimiento, tal como la
palanca de cambio de velocidades, el freno de
mano, y los pasamanos de los asientos. No coloque
el cableado en lugares que se calientan, tal como
cerca de la salida de un calefactor. Si el material
aislante del cableado se derritiera o se gastara,
habrá el peligro de un cortocircuito del cableado a
la carrocería del vehículo.

No pase el conductor amarillo a través de un orifi-
cio en el compartimiento del motor para conectar a
la batería. Esto dañará el material aislante del con-
ductor y causará un cortocircuito peligroso.

No acorte ningún conductor. Si lo hiciera, la pro-
tección del circuito podría fallar al funcionar
cuando debería.

Nunca alimente energía a otros equipos cortando el
aislamiento del conductor de alimentación provista
de la unidad y haciendo un empalme con el con-
ductor. La capacidad de corriente del conductor se
excederá, causando el recalentamiento.

Cuando reemplace el fusible, asegúrese de utilizar
solamente un fusible del ratio especificado para
esta unidad.

Ya que se emplea un circuito único BPTL, nunca
coloque los cables de manera que los conductores
del altavoz estén directamente en conexión a tierra
o que el altavoz izquierdo y derecho ≠ sean
comunes.

Los altavoces conectados a esta unidad deben ser
del tipo de alta potencia con un régimen mínimo de
50 W y una impedancia de 4 a 8 ohmios. La
conexión de altavoces con valores de impedancia
y/o de salida diferentes a los anotados aquí podrían
causar fuego, emisión de humo o daños a los altav-
oces.

Cuando se conecta la fuente de este producto, una
señal de control se emite a través del conductor
azul/blanco. Conecte al control remoto de sistema
de un amplificador de potencia externo o al termi-
nal de controle de relé de antena automática del
vehículo (máx. 300 mA 12 V CC). Si el vehículo
tiene una antena en vidrio, conecte al terminal de
suministro de energía de la antena.

Cuando se está utilizando un amperio de potencia
externa con este sistema, asegúrese de no conectar
el conductor azul/blanco al terminal de potencia de
amperios. Asimismo, no conecte el conductor
azul/blanco al terminal de potencia de la auto-ante-
na. Tal conexión podría causar la fuga de corriente
excesiva y causar fallos de funcionamiento.

Para evitar cortocircuitos, cubra o conductor
desconectado con cinta aislada. Aísle los conduc-
tores de altavoz no usados sin falta. Hay la posibil-
idad de cortocircuito si no se aíslan los conduc-
tores.

Para evitar la conexión incorrecta, el lado de en-
trada del conector IP-BUS es azul, y el lado de
salida es negro. Conecte los conectores del
mismo color correctamente.

Si se instala esta unidad en un vehículo que no
tiene una posición ACC (accesorio) en el interrup-
tor de encendido, el conductor rojo de la unidad
deberá conectarse al terminal conectado con las
operaciones del interruptor de encendido ON/OFF.
Si no se hace esto, la batería del vehículo podría
drenarse cuando usted esté lejos del vehículo por
varias horas.

El conductor negro es la masa. Conecte a masa
este conductor separadamente desde la masa de
los productos de alta corriente tal como los
amplificadores de potencia.
Si conecta juntos a masa los productos y la masa
se desconecta, se crea el riesgo de daños a los
productos o de incendios.

Los cables para este producto y aquéllas para
otros productos pueden ser de colores diferentes
aun si tienen la misma función. Cuando se
conecta este producto a otro, refiérase a los
manuales de ambos productos y conecte los
cables que tienen la misma función.

Conexión de las unidades

Posición ACC

ACC

ON

S

T

A

R

T

O

FF

ON

S

T

A

R

T

O

FF

No en la posición ACC

<ESPAÑOL>

Diagrama de conexión (Fig. 12)

1. Este producto
2. Salida de altavoz de graves secundario o salida

sin atenuación

3. Salida delantera (FRONT OUTPUT)
4. Jack para antena
5. Cable IP-BUS
6. Entrada IP-BUS (Azul)
7. Toma para el control remoto con hilo

Consulte el manual de instrucciones para el con-
trol remoto con hilo (en venta por separado).

8. Reproductor de Multi-CD

(en venta por separado)

9. Fusible
10. Nota:

Dependiendo del tipo del vehículo, la función de
3* y 5* puede ser diferente. En este caso,
asegúrese de conectar 2* a 5* y 4* a 3*.

11. Conecte los conductores del mismo color uno a

otro.

12. Tapa (1*)

Cuando este terminal no se usa, no retire la tapa.

13. Amarillo (3*)

Reserva (o accesorio)

14. Amarillo (2*)

Al terminal con suministro constante de
electricidad, independientemente de la posición
del interruptor de encendido.

15. Rojo (5*)

Accesorio (o reserva)

16. Rojo (4*)

Al terminal de energía eléctrica controlado por el
interruptor de encendido del vehículo (12 V CC)
ON/OFF.

17. Negro (masa)

A la carrocería del vehículo (parte metálica).

18. Conector ISO

Nota:
En algunos vehículos, el conector ISO puede
estar dividido en dos partes. En este caso,
asegúrese de conectar a ambos conectores.

19. Amarillo/negro

Si utiliza un teléfono celular, conéctelo por el
cable de enmudecimiento de audio del teléfono
celular. Si no, mantenga el enmudecimiento de
audio libre de cualquier conexión.

20. Cables de altavoz

Blanco

: Izquierdo delantero +

Blanco/negro : Izquierdo delantero ≠
Gris

: Derecho delantero +

Gris/negro

: Derecho delantero ≠

Verde

: Izquierdo trasero +

Verde/negro : Izquierdo trasero ≠
Violeta

: Derecho trasero +

Violeta/negro: Derecho trasero ≠

21. Cables de conexión con clavijás RCA (en venta

por separado)

22. Amplificador de potencia (en venta por separado)
23. Azul/blanco

Al terminal de control del sistema del amplifi-
cador de potencia (máx. 300 mA 12 V CC).

24. Control remoto de sistema
25. Azul/blanco (7*)

Al terminal de control de relé de antena
automática (máx. 300 mA 12 V CC).

26. Azul/blanco (6*)
27. La posición de los pinos del conector ISO difiere

de acuerdo al tipo de vehículo. Conecte 6* y 7*
cuando el pino 5 es un tipo de control de antena.
En otros tipos de vehículo, nunca conecte 6* y
7*.

28. Altavoz delantero
29. Izquierda
30. Derecha
31. Altavoz de graves secundario
32. Lleve a cabo estas conexiones cuando utilice el

amplificador opcional.

33. Nota:

Cambie el ajuste inicial de esta unidad (refiérase
al manual de operación). La salida de altavoz de
graves secundario de esta unidad es monofónica.

Note:

This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.

To avoid shorts in the electrical system, be sure
to disconnect the ≠ battery cable before begin-
ning installation.

Refer to the owner’s manual for details on con-
necting the power amp and other units, then
make connections correctly.

Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.

Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.

Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.

Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.

When replacing the fuse, be sure to only use a
fuse of the rating prescribed on this product.

Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right ≠ speaker leads are com-
mon.

Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers
catching fire, emitting smoke or becoming dam-
aged.

When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.

When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.

To avoid a short-circuit, cover the disconnected
lead with insulating tape. Insulate the unused
speaker leads without fail. There is a possibility
of a short-circuit if the leads are not insulated.

To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.

If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.

The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.

Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
manuals of both products and connect cords that
have the same function.

Connecting the Units

<ENGLISH>

Connection Diagram (Fig. 12)

1. This product
2. Subwoofer or non fading output
3. Front output (FRONT OUTPUT)
4. Antenna jack
5. IP-BUS cable
6. IP-BUS input (Blue)
7. Jack for the Wired Remote Control

Please see the Instruction Manual for the Wired
Remote Control (sold separately).

8. Multi-CD player (sold separately)
9. Fuse
10. Note:

Depending on the kind of vehicle, the function of
3* and 5* may be different. In this case, be sure
to connect 2* to 5* and 4* to 3*.

11. Connect leads of the same color to each other.
12. Cap (1*)

When not using this terminal, do not remove the
cap.

13. Yellow (3*)

Back-up (or accessory)

14. Yellow (2*)

To terminal always supplied with power regard-
less of ignition switch position.

15. Red (5*)

Accessory (or back-up)

16. Red (4*)

To electric terminal controlled by ignition switch
(12 V DC) ON/OFF.

17. Black (ground)

To vehicle (metal) body.

18. ISO connector

Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.

19. Yellow/black

If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connec-
tions.

20. Speaker leads

White

: Front left +

White/black : Front left ≠
Gray

: Front right +

Gray/black : Front right ≠
Green

: Rear left +

Green/black : Rear left ≠
Violet

: Rear right +

Violet/black : Rear right ≠

21. Connecting cords with RCA pin plugs (sold

separately)

22. Power amp (sold separately)
23. Blue/white

To system control terminal of the power amp
(max. 300 mA 12 V DC).

24. System remote control
25. Blue/white (7*)

To Auto-antenna relay control terminal
(max. 300 mA 12 V DC).

26. Blue/white (6*)
27.The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.

28. Front Speaker
29. Left
30. Right
31. Subwoofer
32. Perform these connections when using the

optional amplifier.

33. Note:

Change the initial setting of this unit (refer to the
Operational Manual). Subwoofer output of this
unit is monaural.

ACC position

ACC

ON

S

T

A

R

T

O

FF

ON

S

T

A

R

T

O

FF

No ACC position

Advertising