Operating the tv with the player’s remote control, Perating the tv with the player’s remote control – Pioneer BDP-320 User Manual

Page 19

Advertising
background image

19

En

03

– To listen to audio with the

player connected to an

AV

receiver or amplifier with an HDMI cable,

connect the TV to the AV

receiver or amplifier using

an HDMI cable (

page 15).

• When

HDMI or DIGITAL AUDIO is selected at Audio,

linea

r PCM audio signals (2 channels) are output

f

rom all terminals other than the ones selected at

Audio.

• When

ANALOG AUDIO is selected at Audio, no

audio signals a

re output from the

HDMI OUT or

DIGITAL OUT terminals.

For steps 5 to 7, the step to which you should
proceed depends on the combination of the Video
and Audio settings.

5

Select and set the HDMI High Speed Transmission

setting for the HDMI OUT terminal.
Use

/ to select, then press ENTER.

When

HDMI High Speed Transmission for the HDMI

OUT terminal is set to On, use a High Speed HDMI™
cable. The

picture and sound may not be output properly

if any othe

r HDMI cable (for example a standard HDMI™

cable) o

r an HDMI cable with built-in equalizer is used.

6

Select the output video resolution from the

COMPONENT VIDEO output terminals.
Use

/ to select, then press ENTER.

Fo

r details on the resolution settings, see Switching the

output video resolution on page 21.

7

Select the aspect ratio of your TV.

Use

/ to select, then press ENTER.

8

Check the settings.

Select

Proceed, then press ENTER.

9

Output test tones.

Use

/ to select Yes, then press ENTER.

10 Finish the Setup Navigator menu.
Use

/ to select Finish, then press ENTER.

To

redo the settings from the start, select

Go Back.

De

pending on the output terminal setting of step 4 or the

HDMI cable being used, it may ha

ppen that no picture

and/o

r sound is output. If this happens, the setup returns

to ste

p 4 if there is no operation for over 30 seconds. Once

the setu

p returns to step 4, redo the settings according to

the connected devices and the HDMI cable being used.

11 Checking the picture quality settings or setting
the picture quality
If a Pionee

r Flat Screen TV or projector is connected to the

player and

HDMI is selected for Video in step 4, the

player sets the picture quality automatically. The
automatic

picture quality setting screen appears. Press

ENTER.

When the automatic

picture quality setting screen does

not a

ppear, the manual picture quality setting screen

a

ppears. Use

/ to select the connected component,

then

press

ENTER.

Operating the TV with
the player’s remote
control

When the manufactu

rer code for your brand of TV is set

on the

player’s remote control, the TV can be operated

using the

player’s remote control.

Caution

• Fo

r some models it may not be possible to operate the

TV with the

player’s remote control, even for TVs of

b

rands listed on the manufacturer code list.

• The setting may be

restored to the default after the

batte

ries are replaced. If this happens, reset it.

1

Input the 2-digit manufacturer code.

P

ress the number buttons (0 to 9) to input the code while

pressing

TV CONTROL

.

Note

• The facto

ry setting is 00 (PIONEER).

• If you make a mistake when in

putting the code,

release

TV CONTROL

 then start over from the

beginning.

• When the

re are multiple codes for a manufacturer, try

in

putting them in the indicated order until the TV can

be o

perated.

2

Check that the TV can be operated.

O

perate the TV using

TV CONTROL.

 – Press to turn the TV’s power on and off.
INPUT SELECT – Press to switch the TV’s input.

CH +/– – Press to select the TV channel.

VOL +/– – Press to adjust the volume.

TV CONTROL

STANDBY/ON

OPEN/CLOSE

AUDIO SUBTITLE ANGLE FL DIMMER

ENTER

INPUT

SELECT

CH

VOL

AUDIO

VIDEO

OUTPUT

RESOLUTION

CLEAR

320_VXJ5_IBD_EN.book 19 ページ 2009年2月25日 水曜日 午前10時57分

Advertising