Pioneer BDP-320 - Manual (Page 56)

07
56
En
No picture is displayed or the
picture is not displayed
properly.
Is the video cable properly
connected?
• Connect the cable properly according to the connected devices
( page 13).
• Inse rt the cable firmly and all the way in.
Is the video cable damaged? If the cable is damaged, replace it with a new one.
Is the in put setting on the
connected TV o r AV receiver
o r amplifier right?
Read the o perating instructions of the connected components and
switch to the proper input.
A re you viewing the picture
f rom the video output
te rminal selected with VIDEO
SELECT?
P ress VIDEO SELECT to switch the video output terminal to be viewed
( page 21).
Is the out put video resolution
properly set?
Use OUTPUT RESOLUTION to switch to a resolution at which the video
and audio signals a re output (page 21).
• Is the player connected
with an HDMI cable othe r
than a High S peed HDMI™
cable (with a Standa rd
HDMI™ cable)?
• A re you using an HDMI
cable with built-in equalize r?
1080 p or Deep Color video signals may not be output properly,
de pending on the HDMI cable being used or the player’s settings.
P ress  while pressing  on the player’s front panel to restore the
video out puts to the factory default settings. After this, if you wish to
out put the video signals with 1080p or Deep Color, connect the TV
using a High S peed HDMI™ cable without built-in equalizer, then reset
the player using the Setup Navigator (page 18).
Does the connected TV
su
pport the frame rate of the
video signal being out put by
the player?
If the picture is not displayed when playing a disc with a frame rate that
is not su pported, the picture will not be displayed even when playback
is sto pped. In this case, use the procedure below to switch the frame
rate of the video signals output from the player.
Eject the disc and close the disc t
ray. Then, press  OPEN/CLOSE
while pressing  on the player’s front panel to switch to a frame rate
su pported by the connected TV.
Is NTSC on PAL TV properly
set?
When viewing the video signals out put from the player’s S-Video or
Video te rminal, set NTSC on PAL TV properly (page 37).
Is a DVI device connected? The picture may not be displayed properly if a DVI device is connected.
Is HDMI Color Space
properly set?
Change the HDMI Color Space setting (page 38).
Pictu re freezes and the front
panel and remote control
buttons sto
p working.
• P ress  STOP to stop playback, then restart playback.
• If the playback cannot be stopped, press  STANDBY/ON on the
player’s front panel to turn off the power, then turn the power back on.
• If the power cannot be turned off, press and hold  STANDBY/ON
on the player’s front panel for over 5 seconds. The power will turn off.
Motion is unnatu ral or
picture is not clear.
Change the Pure Cinema setting (page 34).
No picture is displayed or
picture is not output in high
definition when
playing BDs.
With some discs, it may not be possible to output the video signals from
the VIDEO output terminal or the COMPONENT VIDEO output
te rminals. In this case, connect using an HDMI cable (page 13).
• Pictu re is disturbed during
playback.
• Pictu re is dark.
• This player supports Macrovision analog copy protection technology.
With some TVs (such as with built-in video deck), the picture will not be
dis played properly when the copy protected DVD title is played. This is
not a malfunction.
• If the player and TV are connected via a DVD recorder/video deck,
etc., the picture will not be displayed properly due to analog copy
protection. Connect the player and TV directly.
Problem Check Remedy
320_VXJ5_IBD_EN.book 56 ページ ２００９年２月２５日 水曜日 午前１０時５７分