Aironet Lan Adapter User Manual
User’s guide and technical reference manual, Aironet wireless lan adapter
Advertising
Table of contents
Document Outline
- Table of Contents
- List of Figures
- List of Tables
- Protocols Supported
- Terminology
- Standard Antennas
- Attaching the Antenna
- Detaching the Antenna
- Installing the Wireless LAN Adapter
- Windows 95 or Windows 98 NDIS3 Installation
- 1. Power on your computer and boot Windows.
- 2. Insert the adapter into one of the PC Card slot...
- 3. Windows will display the New Hardware Found 3. ...
- 4. Select the Driver from disk provided by hardwar...
- 5. Insert the driver disk provided with the adapte...
- 6. Type A:\NDIS3 at the prompt and press Enter.
- 7. Select the appropriate LAN Adapter and press En...
- 8. Select the appropriate Infrastructure Mode and ...
- 9. Optionally, select the Channel and Bitrate para...
- 10. Press Enter.
- 11. Windows will prompt for the system disks. Ente...
- 12. Restart Windows after the files are copied. Th...
- Windows NT NDIS3 Installation
- 1. Shutdown the Windows NT workstation.
- 2. Insert the Wireless LAN Adapter into one of the...
- 3. Power up the Windows NT workstation.
- 4. From the control panel, select the Network icon...
- 5. Select Adapters.
- 6. Select Add.
- 7. Select Have Disk.
- 8. Insert the driver disk provided with the adapte...
- 9. Type A:\NDIS3 at the prompt and press Enter.
- 10. Select OK when the dialog box shows Aironet PC...
- 11. Select the appropriate parameters, such as Inf...
- 12. Verify that the Interrupt and IO Base Address ...
- 13. Select OK.
- 14. Select Close.
- 15. Add all other related network information if a...
- 16. Select Yes to restart the workstation.
- Windows for Workgroups NDIS2 Installation
- 1. Power on your computer and start Windows for 1....
- 2. Go to the Network program group and click on Ne...
- 3. Under Network Setup, choose Networks.....
- 4. Under Networks choose Install Microsoft Windows...
- 5. Under Network Setup, choose Drivers....
- 6. Under Network Drivers, choose Add Adapters.
- 7. If the drivers were already copied to the hard ...
- 8. Under Add Adapter, choose the appropriate Airon...
- 9. Place the driver disk in drive A.
- 10. Type A:\NDIS2\ at the prompt and press Enter.
- 11. Choose the correct Aironet Adapter and click O...
- 12. If the chosen adapter is displayed in the Netw...
- 13. Select the appropriate parameters, such as Inf...
- 14. Exit Windows for Workgroups.
- 15. To modify the PC Card system parameters, edit ...
- 16. Reboot your computer.
- DOS NDIS2 Installation
- DOS Packet Driver Installation
- ODI Driver Installation
- General Information
- Driver Keywords and Settings
- Section 4
- Utilities
- Site Survey and Link Test
- Using Windows 3.11 or DOS to Perform a Link Test U...
- 1. Install the drivers.
- 2. Configure the drivers for network operation.
- 3. Ensure unique IP assignments of mobile/portable...
- 4. Set up an Aironet Access Point for the intended...
- 5. Start the operating system on the mobile statio...
- 6. Configure the adapter.
- 7. Make sure the mobile station is associated to t...
- 8. Start a telnet session on the mobile station to...
- 9. Navigate through the Aironet Access Point menu ...
- 10. Set up the test options to accurately model th...
- 11. Set the test for continuous operation with a 1...
- 12. Begin traversing the area around the Aironet 1...
- Using Windows 95 or Windows 98 to Perform a Link T...
- Using Windows 3.11 or DOS to Perform a Link Test U...
- Site Survey and Link Test
- Link Test Command in WinDGS
- Loading New Firmware Versions
- Options Menu