Binatone 1505 User Manual

User guide

Advertising

THIS EQUIPMENT IS NOT DESIGNED FOR MAKING

EMERGENCY TELEPHONE CALLS WHEN THE POWER

FAILS. ALTERNATIVE ARRANGEMENTS SHOULD BE

MADE FOR ACCESS TO DIAL EMERGENCY SERVICES.

Before operating this set,

please read these instructions carefully.

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always

be followed to reduce the risk of fire, electric shock and injury, including the

1) Read and understand all the instructions.
2) Follow all warnings and instructions marked on the product.
3) Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

sink, swimming pool).

5) Do not overload wall outlets and extension cords as this can result in the risk

of fire or electric shock.

6) Unplug this product from the wall outlet and refer servicing to our Repair

•

When the power supply cord or plug is damaged or frayed.

• If the product does not operate normally by following the operating instructions.

•

If the product has been dropped and the cabinet has been damaged.

•

If the product exhibits a distinct change in performance.

7) NEVER use your

8) Do not use the telephone to report a gas leak in the vicinity of the leak.
9) Use only the supplied NiMH (Nickel Metal Hydride) batteries! The operation

periods for the handsets are only applicable with the default battery capacities

10) The use of other battery types or non-rechargeable batteries/primary cells

can be dangerous. These may cause interference and/or damage to the unit

or surroundings. The manufacturer will not be held liable for damage arising

from such non-compliance.

11) Do not use third party charging bays. Damage may be caused to the batteries.
12) Please ensure the batteries are inserted in the correct polarity.
13) Dispose of batteries safely. Do not immerse them in water, burn them, or put

them

where they could get punctured.

Centre under the

following conditions:

following:

GETTING TO KNOW YOUR PHONE

Indicates when the battery needs charging.

Flashes when low battery power level is detected.

(BACK)

(INT)

Indicates when there are more characters or numbers in front of those

Indicates when there are more characters or numbers after those being

Press the MENU/OK key to access the main menu.
Press the MENU/OK key to confirm the current selection.
Indicates a new Call List entry is being

Press the C/MUTE key to start an intercom call.

Press the C/MUTE key to go back to the previous menu level or cancel

Press the C/MUTE key to clear a character, stop the alarm, or mute/unmute

being displayed.

displayed.

the current action.

the microphone during a call.

3.4 Menu

Structure

In idle mode, press <MENU/OK>

Refer to the following for the menu structure.

3.5 Text and Digit Entry Table
The following table shows you where each letter and punctuation character can

be found, by using repeated presses of the alphanumeric keypad. This will be

helpful when storing a name in the phonebook and renaming your handset.

In editing mode, a cursor is displayed to indicate the current text entry position.

It is positioned at the right of the last character entered.
Writing Tips:
1. Once a character is selected, the cursor will move to the next position after a

short pause.

2. You can move the cursor within the text with the <UP/DOWN> keys to

amend the text entry.

3. Press <C> to delete the last character.

4. Press and hold <C> to delete the entire text string.

4.3 End a Call

During a call press <TALK OFF> to end the call.

Put the handset on the base station or charger to end the call.

4.4 Adjust Earpiece Volume

During a call:

setting is shown.

When you end the call, the setting will remain at the last selected level.
4.5 Mute

Call

You can talk to someone nearby without letting the caller hear you during a call.

During a call:

Press <C> to mute the microphone and “MUTED” will display on the LCD.

Your caller cannot hear you. Press <C> again to unmute the microphone.
4.6

the

In idle, press and hold <HASH/#> to turn off the handset ringer. The “RINGER

OFF”

icon is displayed on the LCD.

4.7 Turn on the Keypad Lock

In idle, press and hold <STAR/*> to turn on the keypad lock. The

4.8 Redial the last number
You can redial any of the 5 last numbers called. If you have stored a name in

the phonebook to go with the number, the name will be displayed instead.

4.8.1 Redial a Number from the Redial List

1. ress <

Note: If the redial list entry shows a name, press <Hash/#> to view the number

2. Press <UP/DOWN> to browse the redial list.

3. Press <TALK ON> to dial to the selected redial number.

Note: If there are no numbers in the redial list, the display shows “EMPTY ”.

4.8.2 Store a Redial Number into the Phonebook
1. Follow Steps 1 and 2 in section 4.8.1.

2. Press <MENU> and <UP/DOWN> to select

ADD TO PB.

3. Press <OK> and then enter the name you want to use in the phonebook.

4. Press <OK> and then modify the number, if necessary.

5. Press <OK> to show <MELODY 1>.

6. Press <UP/DOWN> to browse the ringtone list. The respective ringtone will

be played when browsing the ringtone list. (Note: the selected melody will

7. Press <OK> to confirm, and the entry will be stored.

Note: The display will still flash the Call icon and show CALL or the Caller Display

number, when there is an incoming call, even if the ringer is turned off

To turn the ringer back on, press and hold <HASH/#> again.

Note: You can still use <TALK ON> to answer a call

To turn the keypad lock off, press and hold <STAR/*> again.

only be played if you subscribe to Caller Display and the incoming number

icon is displayed on the LCD.

The most recent last number will display at the top of the redial list.

of this entry.

matches the stored number.)

4.8.3 Delete a Redial Number
1. Follow Steps 1 and 2 in section 4.8.1.

2. Press <MENU> and <UP/DOWN> to select

DELETE.

3. Press <OK> to confirm, and the entry will be deleted.

4.9 Find the Handset
You can locate the handset by pressing <PAGE> on the base station. All the

handsets registered to the base will produce the paging tone and show

4.8.4 Delete all Redial List entries
1. Follow Steps 1 and 2 in section 4.8.1.

2. Press <MENU> and <UP/DOWN> to select

DELETE ALL

3. Press <OK> to display <CONFIRM?>.

4. Press <OK> to confirm. All entries will be deleted and the display will show

<EMPTY>.

<TALK OFF> /<C> on any handset or <PAGE> on the base again.
Note: If there is an incoming call during paging, the phone will ring with the

4.10 Make an Internal Call (For multi-handset versions only)
This feature is only applicable when there are at least two registered handsets.

It allows you to make internal calls, transfer external calls from one handset to

incoming call instead of paging.

LOCK”

"PAGING" on the display. You can stop the paging by pressing <TALKON>/

another handset and make conference calls. If the called handset is not

answered within 60 seconds, the called handset will stop ringing and the calling

Note: If only one handset is registered to the base station, when <C/MUTE/INT>

is pressed, it will display

“NOT POSSIBLE”

4.10.1 Intercom Another Handset

1. In idle mode, press <C/MUTE/INT> and all the other registered handset

2. Enter the number of the handset that you want to call, or enter "9" to call all

3. The called handset rings and <TALK ON> must be

Note: If only two handsets are registered to the base station, pressing

<C/MUTE/INT> will call the other handset immediately.

numbers will display, along with a "9".

to establish the intercom call.

4.10.3 Transfer an External Call to another handset
During an external call:

1. Press <MENU> and <UP/DOWN> to select

INTERCOM.

2. Press <OK> to show all the other registered handset numbers, plus "9".

3. The external call is put on hold automatically and the called handset rings.

4. Press <TALK ON> on the called handset to establish

Enter the

number for the handset you want to transfer the call to.

handset will return to standby mode.

handsets.

5. Press <TALK OFF> on the calling handset or put the calling handset on the

charging cradle to end the current call with the external party.

6. The external call is transferred to the called handset.

4.10.2 Call All Handsets

1. In idle mode, press <C/MUTE/INT> and the registered handsets will display.

2. Press digit key <9> to ring to all registered handsets

4.10.4 Make a 3-way Conference Call
The conference call feature allows one external call to be shared with two

handsets (in intercom).
The three parties can share the conversation and no additional network

subscription is required.

During an external call:
1. Follow Steps 1 to 4 in section 4.10.3.

2. Press and hold <STAR> on the calling handset to establish the conference call

Either handset can exit the conference by pressing <TALK OFF>, leaving the

other handset still connected to the external call.

5 PRIVATE

PHONEBOOK

pressed on that handset

an internal call.

handset is ringing.

when the

near water (for example, near

a bath tub, kitchen

Keep your

se this product

and don't let it get wet or u

base from the telephone line and the mains socket when there are storms

in your area. Damage caused by l

ightning is not covered by the guarantee.

Speakerphone

Your handset's loudspeaker is on.

Speakerphone

Your handset's loudspeaker is on.

to go to CALL LIST, the first option in the menu list.

Press <UP> or <DOWN> to go to other options in the menu list.

Press <MENU/OK> to enter a sub-menu or function.
Press <C/MUTE> to go back to the previous level.

ress <UP/DOWN> to select volume 1-5. The current

Turn off

Handset Ringer

Note: If there is an external call while you are on an intercom call, you'll

hear warning beeps, and you have to end the intercom all, before you can

answer the external call.

Note: If the other handset has not answered the intercom call, you can stop

the intercom and return to the external call by pressing <TALK OFF>

TECHNICAL DETAILS

Standard

Frequency range
Channel bandwidth
Operating range
Operating time

Temperature range

Digital Enhanced Cordless

Telecommunication (DECT)

1.88 to 1.9 GHz
1.728 MHz
Up to 300m outdoors; up to 50m indoors
Standby: 100 hours, Talking:

10 hours

Battery charge time:15 hours
Operating 0 C to 40 C

(bandwidth = 20 MHz)

Port specification

The

port (connec ted to the mains power supply) is a

SELV port with respect to EN41003.

CLEANING AND CARE

Do not clean any part of your phone system with benzene, thinners or other

solvent chemicals - this may cause permanent damage which is not covered by the

Guarantee.

When necessary, clean it with a damp cloth.

Keep your phone system away from

hot, humid conditions or strong

and

don't let it get wet.

Every effort has been made to ensure high standards of reliability for your

do not try to

, Storage -20 C to 60 C

Caution
Risk of explosion if battery is replaced by an incorrect type
Dispose of used batteries according to the instructions.

The port (connected to the telephone line) is aTNV port with respect to EN41003.

repair it yourself

sunlight,

, consult your supplier or the Helpline.

Main

CALL LIST

PHONEBOOK

SETTINGS

REGISTRATION

DEFAULT

Sub

ADD TO PB

DELETE

DELETE ALL

phonebook Entry.

ADD

VIEW

EDIT

DELETE

DELETE ALL

PB STATUS

DELETE HS

DIAL MODE

FLASH TIME

ALARM

RING SETUP

TONE SETUP

LANGUAGE

RENAME HS

HS DISPLAY

AUTO ANSWER

DATE & TIME

PIN? - - - -

<UP/DOWN>

Key Press

<MENU>

<UP/

DOWN>

<UP/

DOWN>

<UP/

DOWN>

<UP/

DOWN>

<UP/

DOWN>

Shows EMPTY

or the first Call

List Entry. Then

<OK> for:

Shows EMPTY

or the first

Then <OK> for:

ADD

PB STATUS

CHANGE PIN

DETAILS

Each handset can store up to 20 private phonebook entries with names and

numbers. Each phonebook entry can have a maximum of 20 digits for the

phone number and 12 characters for the name. You can also select different

ringtones for your phonebook entries. (Note: the different ringtones only play if

5.1 Add a New Phonebook Entry
In idle:

1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

<OK> to access the phonebook.

2. Press <MENU> to show ADD.

3. Press <OK> and then enter the name.

4. Press <OK> and then enter the number.

5. Press <OK> and <UP/DOWN> to select the desired ringtone for your

6. Press <OK> to store the phonebook entry.

you subscribe to Caller Display and the incoming number matches the stored

number.) Phonebook entries are stored alphabetically by name.

phonebook entry.

5.2 Search for a Phonebook Entry

In idle:

1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

2. Enter the first letter of the name using the alphanumeric keys(e.g. if it

want.

5.3 View a Phonebook Entry

In idle:

1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

<OK> to access the phonebook.

2. Press <UP/DOWN> to select the desired phonebook entry.
3. Press <MENU> and <UP/DOWN> to select

VIEW.

4. Press <OK> and <UP/DOWN> to review the name, number and ringtone

of the selected phonebook entry.

Note: If the number is more than 12 digits, press <LEFT SOFT KEY> or

<RIGHT SOFT KEY> to view the remaining digits.

and then <UP/DOWN> to scroll to the entry you

begins with C, press the 2 key three times),

<OK>

to access the phonebook.

5.4 Edit a Phonebook Entry

In idle:

1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

to access the phonebook.

2. Press <UP/DOWN> to select the desired phonebook entry.

3. Press <MENU> and <UP/DOWN> to select

EDIT.

4. Press <OK> to display the current name.

5. Edit the name and press <OK>.

6. Edit the number and press <OK>.

7. Press <UP/DOWN> to select the ringtone and press <OK> to confirm.
5.5 Delete a Phonebook Entry

In idle:

1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

to access the phonebook.

2. Press <UP/DOWN> to select the desired phonebook entry.

3. Press <MENU> and <UP/DOWN> to select

DELETE.

4. Press <OK> to confirm, and the entry will be deleted.
5.6 Delete all Phonebook entries

1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

Press <MENU> and <UP/DOWN> to select

DELETE ALL.

Press <OK> to display <CONFIRM?>.

Press <OK> to confirm. All entries will be deleted and the display will show

<EMPTY>.

5.7 Check the Phonebook Usage
You can check how many phonebook entries are stored in your handset and

how many phonebook entries are available for you to store in the phonebook.
1. Press <MENU> then <UP/DOWN> to select PHONEBOOK and then press

to access the phonebook.

2. Press <MENU> and <UP/DOWN> to select

PB STATUS.

3. Press <OK> to display how much of the phonebook is being used,

for example < 6/ USED> means 6 entries are stored out of the

total available spaces.

<OK>

<OK> to access the phonebook.

<OK>

If the call is from someone who withheld their number, e.g. by dialling 141,

will display.

If the call is from someone whose number is unavailable, e.g. an international

call or from a private exchange, “OUT OF AREA” will display.
If you've got new Caller Display records, the handset will display "X NEW

6.1 View the Call List
All received calls are saved in the Call List,
When the call list is full, the oldest call will be replaced by a new call. Any

unanswered calls which have not been viewed are marked with a <*> icon at the

CALLS" in standby mode. The New Calls indication will remain until all the new

call records have been viewed on that handset.

centre of the bottom line of the display.

1. Press <UP> to access the call list.

OR Press <MENU> and <UP/DOWN> to show CALL LIST, then press OK.

2. Press <UP/DOWN> to select the desired entry.

3. Press <#> to view the caller’s number if applicable.

6.2 Store a Call List Number into the Phonebook
1. Follow Steps 1 and 2 in Section 6.1.

2. Press <MENU> and <UP/DOWN> to show

ADD TO PB.

3. Press <OK> and then enter the name.

4. Press <OK> and the selected call list number is displayed.

5. Edit the number if necessary.

6. Press <OK> and <UP/DOWN> to select the ringtone.

7. Press <OK> to store the phonebook entry and return to the calls list.

4. Press <MENU>, <UP/DOWN> to show

DETAILS, and then <OK> to display

the date and time of the call. Press <OK> to go back to the previous screen.

“WITHHELD”

CALLER DISPLAY (NETWORK DEPENDENT)

This feature is available if you have subscribed to the Calling Line Identification

service with your network service provider. Your phone can store up to 10

received calls with date/time information in the Call List. The number will be

shown on the handset display when the phone is ringing. If the number matches

with one of the entries in your Private Phonebook, the caller’s name stored in the

private phonebook will be displayed alternately with the number, and the

handset will ring with the ringtone associated with that phonebook entry.

with the latest call at the top of the list.

2 INSTALLING YOUR PHONE

2.1 Connecting the base station

1) Plug the power supply and line cord

2) Plug the power adapter into a 230Vac,

3) Always use the cables provided in the box

Warning: Use only the provided adaptor, using

other power supplies may cause a hazard.

50Hz mains socket, and the line cord into your

2.2 Installing and charging the batteries

1) Place the 2 supplied batteries into the battery

3) Put the handset on the base and charge for

15 hours before using the handset for the first time.

If you have a Broadband line

If you connect your telephone to a line with

insert a micro-filter between the telephone

and the telephone line, otherwise you may get

interference between the telephone and the broadband,

which could cause problems.

a broadband connection, you will need to

telephone line socket.

Warning: Install the base unit in a position where

mains power cable.
Note: The base unit needs mains power for normal
operation, not just for charging the handset batteries.

Use only the NiMH rechargeable battery type

2) Position the battery compartment cover over the

In a home with broadband, every telephone must have a micro-filter connected,

not just the one at the telephone point that your modem is connected to.

If you need more broadband micro-filters, contact your broadband supplier.

compartment with the polarity markings as shown

The handset will give a beep when it is properly

into the base station.

batteries and slide up to click into place.

placed on the base or charger.

the mains adapter plug will reach an easily
accessible mains socket. Never try to lengthen the

provided.

Indicates you can scroll

up / down the menu items / Phonebook list /

Steady when the handset is in range of the base. Flashes when out of

Steady when an intercom call is in progress.

Flashes when there is an incoming internal call.
Indicates a call is in progress on that handset.

Indicates that the

ringer is switched off.

Steady when an alarm is set. Flashes when the alarm is sounding.
Indicates that the keypad is locked.
Indicates when you have a new Voice Mail message.

(This is a Caller Display service and is not usually available from

range of the base or not registered to the base.

UK network providers.)
Indicates when the battery is fully charged.
Whole icon flashes when the battery s charging.

Internal block icon flashes when the battery is in final charging stage.

handset

Flashes when there is an incoming external call.

3.5.1 Character

Set

Key

Press 1st

3rd 4th 5th 6th 7th 8th 9th 10th

space -

Y Z

0, or P (Pause) if press and hold

(

)

Alphanumeric Editing

(For phonebook name editing and renaming handset )

Number Editing (For phone

number editing,date/time editing)

o ' , - , &

Note: There are some different characters if the handset language is changed

(page 20).

USING YOUR PHONE

4.1 Make a Call

4.1.1 Preparatory

Dialling

Enter the phone number and press <TALK ON>

to dial the number. When entering the number, if you make a mistake,

to delete digits.

4.1.2 Direct

Dialling

Press <TALK ON> to connect to the line and then

4.1.3 Call from the phonebook

Press <MENU/OK>, then <DOWN>, then <MENU/OK> again to access the

phonebook and press <UP/DOWN> to

Press <TALK ON> to dial out the selected phonebook entry.

(Note: if you enter a wrong digit you cannot correct it with the <C> key.)

select the desired phonebook entry.

4.1.4 Call from the Call List (only available with Caller Display)

Press <UP> to access the Call List and press <UP/DOWN> to select the desired

Press <TALK ON> to dial out the selected Call List entry.

Note: You can also access the Call List by pressing <MENU/OK> twice.

4.1.5 Call from the redial list

Press <DOWN> to access the redial list and press <UP/DOWN> to select the

Note: The alphanumeric keys provide a short-cut to find entries beginning with

the corresponding letters.

Call List entry.

desired redial number.

Press <TALK ON> to dial out the selected redial number.

4.1.6 Call

timer

Your handset automatically times the duration of every call.

The call timer is displayed as soon as you answer a call or 15 seconds after

It is shown in hours, minutes and seconds
4.2 Answer a Call

If the handset is not on the charging cradle:

When the phone rings, press <TALK ON> to answer a call.

Note: If AUTO ANSWER is set to ON, then lifting the handset off the base or

charger will answer the call automatically, and no buttons need to be

format (HH:MM:SS).

pressed.

enter the phone number.

press <C>

dialling and remains on the screen for 5 seconds after the end of the call.

to connect to the line and

3.2 Base Station Overview

Press the Page button on the base

station to page your handset(s).
It will ring for approximately 60 seconds.

CHARGING

CRADLE

3.3 Display Icons and Symbols

The LCD display gives you information on the current status of the telephone.

Press and hold to put base into registration mode.

1. PAGE < >

Electrical power

TenPao - S004LB0600030/S004LV0600030 -

Charger unit:
TenPao - S004LB0600030 / S004LV0600030 -

Battery Information

Base unit:

input 100-240VAC 50/60Hz 150mA, output 6VDC 300mA

USER GUIDE

**Please note that all calls are charged at local rate

www.binatoneonline.com

or visit our website:

Binatone Helpline (for UK only)

Monday to Friday from 9:00am to 5:00pm
Tel: 0845 345 9677

displayed.

Redial list / Call List

Solas 1505 system. However, if something does go wrong, please

phone away from hot, humid conditions or strong sunlight,

phone outdoors during a thunderstorm-unplug the

Package contents

The package contains the following items:

• 1 Handset

• 1 Base station

• 1 Mains power adapter

• 1 Telephone line cord

• 2 AAA rechargeable batteries

• 1 User manual

Note: If you have a Twin, Triple or Quad system, you will also have the requisite
extra handset(s) and batteries, and a charger pod for each extra handset.

Handset - Base Connection
1) When purchased, all handsets are already registered to the base unit and should
link to it when they are all powered up.
2) To use your cordless handset and base unit together, you must be able to
establish a radio link between them. The signal between the handset and the base is

> Any large metal object, such as a refrigerator, mirror or filing cabinet, between the
handset and the base unit may block the radio signal.
> Other solid structures, like walls, may reduce the signal strength.
> Other electrical equipment may cause interference and/or affect the range.

3) Do not place close to another telephone, a TV or audio equipment - it may cause
interference.
4) Out of Range warning. If you hear a warning tone during a call, and/or the sound
in the earpiece becomes faint or distorted, you may be going out of range of the base
unit, so move nearer to the base unit within 20 seconds, otherwise the call may be
cut off.

to 300 metres outdoors or 50 metres indoors. Be aware that:

in accordance with the normal standards for a DECT phone: Maximun range up

Connection and Conditions for use:
You can connect your phone to a direct exchange line (DEL) on a local

exchange with its own phone number; to an extension socket connected to a

DEL; or to an extension on an approved compatible PBX. Do not connect as an

extension to a payphone.
The ringer equivalence number (REN) of all equipment (phones, fax machines,
modems, etc.) connected to an exchange line must not add up to more than 4,
otherwise one or more of them may not ring and/or answer calls correctly. This
phone has a REN of 1, and most other elephones have a REN of 1 unless
marked otherwise.

3.1

Handset Overview

2 LEFT SOFT KEY( /OK)
Use with icons on display above, to
open menu and confirm options.

Make or answer calls

Use with icons on display above, to

8 R - RECALL (also called Flash)
Sends a recall (R) signal, used for some PBX / Calling Features.

7 TALK OFF
End a call or return to previous menu.

1 UP
From idle: access the Call List

Press and hold to turn the handset on / off.

In lists: move up the options
During calls / ringing: increase the volume.

menu, mute the microphone or make

3 TALK ON

(CLEAR/BACK/MUTE/INTERCOM)

6 RIGHT SOFT KEY

clear characters, go back to previous

an intercom call.

GPI - VT
BYD - H-AAA400A 2 x 1.2V AAA size 400mAh NiMH

40AAAHC 2 x 1.2V AAA size 400mAh NiMH

Digital Cordless Telephone

Solas 1505
Solas 1505 Twin
Solas 1505 Triple

There are 5 levels (VOLUME 1 to VOLUME 5) to choose from for the earpiece

volume.

CHARACTER SET

3.5.1

.....................................................................................................

TABLE OF CONTENTS

1 IMPORTANT SAFETY INSTRUCTIONS ..........................................................

2 INSTALLING YOUR PHONE ............................................................................ 5

2.1

.......................................................................... 5

2.2

...................................................... 5

3 GETTING TO KNOW YOUR PHONE................................................................ 6

3.1 HANDSET OVERVIEW ................................................................................................ 6

3.2 BASE STATION OVERVIEW.......................................................................................

3.3 DISPLAY ICONS AND SYMBOLS............................................................................... 7

3.4 MENU STRUCTURE ....................................................................................................

3.5 TEXT AND DIGIT ENTRY TABLE ................................................................................ 9

4 USING YOUR PHONE .....................................................................................

4.1 MAKE A CALL............................................................................................................10

4.1.3 CALL FROM THE PHONEBOOK .............................................................................10

4.1.4 CALL FROM THE CALL LIST(ONLY AVAILABLE WITH CALLER DISPLAY)

...............................................................................

4.1.5 CALL FROM THE REDIAL LIST

4.1.6 CALL TIMER .............................................................................................................10

4.2 ANSWER A CALL ......................................................................................................

4.3 END A CALL ............................................................................................................... 11

4.4 ADJUST EARPIECE VOLUME ..................................................................................

4.5 MUTE A CALL.............................................................................................................

4.6

.................................................................................

4.7 TURN ON THE KEYPAD LOCK .................................................................................

4.8 REDIAL THE LAST NUMBER ....................................................................................

4.8.1 REDIAL A NUMBER FROM THE REDIAL LIST .......................................................

4.8.2

..........................................

4.8.3 DELETE A REDIAL NUMBER ..................................................................................

4.8.4 DELETE ALL REDIAL LIST ENTRIES

..................................................................

4.9 FIND THE HANDSET..................................................................................................

4.10 MAKE AN INTERNAL CALL(FOR MULTI-HANDSET VERSIONS ONLY ) .................

4.10.1

.........................................................................

4.10.2 CALL ALL HANDSETS............................................................................................

4.10.3 TRANSFER AN EXTERNAL CALL TO ANOTHER HANDSET...............................

4.10.4 MAKE A 3-WAY CONFERENCE CALL ..................................................................

.........

TURN OFF HANDSET RINGER

4.1.1 PREPARATORY DIALLING ......................................................................................

4.1.2 DIRECT DIALLING....................................................................................................

11
11

11
12

CONNECTING THE BASE STATION

INSTALLING AND CHARGING THE BATTERIES

STORE A REDIAL NUMBER INTO THE PHONEBOOK

INTERCOM ANOTHER HANDSET

5 PRIVATE PHONEBOOK...................................................................................

5.3 VIEW A PHONEBOOK ENTRY...................................................................................

5.4 EDIT A PHONEBOOK ENTRY....................................................................................

5.5 DELETE A PHONEBOOK ENTRY ..............................................................................

5.6 DELETEALLPHONEBOOKENTRIES

5.7 CHECK THE PHONEBOOK USAGE ..........................................................................

6 CALLER DISPLAY (NETWORK DEPENDENT) ..............................................

6.1 VIEW THE CALL LIST.................................................................................................

6.2 STORE A CALL LIST NUMBER INTO THE PHONEBOOK ......................................

6.3 DELETE AN ENTRY IN THE CALL LIST....................................................................

6.4 DELETE ALL CALL LIST ENTRIES

7 PHONE SETTINGS...........................................................................................

7.1 DATE AND TIME SETTINGS .......................................................................................18

7.1.1 CHANGE THE DATE FORMAT .................................................................................

7.1.2 CHANGE THE TIME FORMAT ..................................................................................

7.1.3 SET THE TIME...........................................................................................................18

7.1.4 SET THE DATE..........................................................................................................18

7.2 ALARM SETTINGS .....................................................................................................

7.2.1 TURN ON/OFF THE ALARM .....................................................................................1 9

7.2.2 SET THE ALARM TIME .............................................................................................1 9

7.3 HANDSET SETTINGS .................................................................................................

7.3.1 SET THE RINGER MELODY FOR INTERNAL CALLS

7.3.2 SET THE RINGER MELODY FOR EXTERNAL CALLS ............................................

7.3.3 SET THE RINGER VOLUME .....................................................................................

7.3.4 SET ALERT TONES...................................................................................................

7.3.5 SET THE HANDSET LANGUAGE .............................................................................

7.3.6 RENAME THE HANDSET..........................................................................................

7.3.7 CHOOSE THE INFORMATION TO BE DISPLAYED IN IDLE ...................................

7.3.8 SET THE AUTO ANSWER ........................................................................................

7.4 BASE SETTINGS .........................................................................................................21

5.1 ADD A NEW PHONEBOOK ENTRY ...........................................................................

5.2

TROUBLESHOOTING ......................................................................................

DECLARATION OF CONFORMITY..................................................................

7.4.1 DE-REGISTER A HANDSET .....................................................................................

7.4.2 CHANGE THE DIAL MODE .......................................................................................

7.4.3 CHANGE THE FLASH (RECALL)TIME .....................................................................

7.4.4 CHANGE THE SYSTEM PIN CODE .........................................................................

7.5

..........................................................................................................23

7.6 RESET YOUR PHONE ................................................................................................

...........................................................................

SEARCH FOR A PHONEBOOK ENTRY

...................................................................

10 GUARANTEE AND SERVICE .........................................................................26

.........................................................................

.............................................

REGISTRATION

REDIAL> to access the redial list.

4 DOWN
In lists: move down the options
During calls / ringing: decrease the
volume

During a call: Press to turn on / off the
speakerphone.
Call List / Phonebook entry : Press to
make a call with speakerphone

During ringing: Press to answer a call
with speakerphone
During answering machine message
playback / call screening:
Press to play message via speaker

5 SPEAKERPHONE ( )

CORUN- NI-MHAAAJ400, Type NiMH (Rechargeable battery)

Voltage Rating 400mAh ,2 X 1.2V AAA Size

Advertising

Popular Brands

Popular manuals