2GIG TS1-E v1-8 Addendum - Manual

PRINTER’S INSTRUCTIONS:
TS1-E ADDENDUM - LINEAR P/N: 232686 X3 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND WITH 80 LB. WHITE COATED COVER - SIZE: FLAT 17.000” x 11.000”, FINISH 8.500” X 11.000” - SCALE: 1-1 - FOLDING: 1 FOLD VERTICAL - FINISH: 3-HOLE STD. DRILL
THE 2GIG-TS1
The new Wireless Touch Screen Keypad, 2GIG-TS1, (referred to as TS1 in this
document) is unlike any other wireless keypad you have seen before. It not only
offers the functionality of a system keypad but also extends all user control of the
2GIG Go!Control panel to other locations in your home. Using the TS1, you can
control your lights, thermostat and door locks and see the status of every zone in
your home using the exact same and familiar interface found on the Go!Control
panel. The TS1 truly is an industry fi rst in offering outstanding two-way interaction
with your 2GIG security and home automation system.
Prerequisites:
• You must have the Go!Control panel (2GIG-CP1-900, referred
to in this document as CP1-900) with the 900 MHz Transceiver
installed in order to use the TS1. The 900 MHz Transceiver
(2GIG-XCVR2) is the communication module that incorporates
a 345 MHz receiver and a 900 MHz transceiver.
• It is assumed that you have general familiarity with 2GIG’s Go!Control
panel programming and the software features currently included in
software release 1.6. If additional information is required in these areas,
please download the installation guides found on www.2gig.com.
LEARNING/PAIRING THE 2GIG-TS1
To learn or pair a TS1 with a CP1-900 panel, you must follow the
steps below:
(1) Make sure that your CP1-900 panel is powered and
operational. Use the supplied AC adapter and confi rm that
the adapter is connected with the correct polarity. Note that
a Go!Control panel without the 900 MHz Transceiver will not
communicate with the TS1.
(2) Make sure the TS1 has power from the supplied AC
transformer. Connect the AC adapter that was supplied with
the TS1 to the TS1. Confi rm that the wires are connected
using the correct polarity.
(3) The TS1 should power up and the following message should
be visible on the display; This Device is Not Paired with a
Control Panel. See example below. Follow the rest of these
steps to correctly pair the TS1 with the CP1-900.
(4) From the CP1-900, enter the Installer Tool Box and select
System Confi guration from the CP1-900. Select the Go To
button and enter 04 to go to question 4. The CP1-900 will
display Q4: select RF keypad # (1 to 4).
(5) Select the RF Keypad number to assign to the TS1. Use
the right arrow button to select the RF Keypad number (1-
4). After selecting the RF Keypad number, press the down
arrow to start confi guring the specifi c parameters for the RF
Keypad you have selected.
(6) Mark the RF Keypad number selected as “used” by pressing
the right arrow to toggle the setting on the fi rst question or by
pressing the number 1 on the keypad. Press the down arrow
key to advance to the next option.
(7) Set RF Keypad Equipment Code to “(1059) 2GIG-TS1
wireless touchscreen keypad”. By pressing the down arrow,
you can select the RF Keypad Equipment Code option. When
the RF Keypad Equipment Code option is selected, pressing
the right or left arrow will toggle through the options. Stop
when the “(1059) 2GIG-TS1 wireless touchscreen keypad”
option is displayed. Press the down arrow key to advance to
the next option.
Release 1.8 and 2GIG-TS1
Technical Support
855-2GIGTECH / 855-244-4832
www.2gig.com