Blue Sea Systems 7520 P12 Battery Charger LED Remote - Manual

Blue Sea Systems Inc. p 360.738.8230
425 Sequoia Drive f 360.734.4195
Bellingham, WA 98226 USA [email protected]
www.bluesea.com
980016790 Rev.001
Warranty
GUARANTEE: Blue Sea Systems stands behind its products for as long
as you own them. Find detailed information at www.bluesea.com/about.
For customer service, call 800-222-7617.
Minimum Operating Temperature −20°C (−4°F)
Maximum Operating Temperature 60°C (140°F)
Minimum Storage Temperature −30°C (−22°F)
Maximum Storage Temperature 70°C (158°F)
Electrical Specification:
On State Operating Current <300mA sourced from charger
Communications:
Protocol Proprietary
Maximum Cable Length 150 ft (45.7 m)
Cable Cat5e (Standard US)
Mounting Hole Cutout 1-1/4" (31.75 mm)
Dimensions Height: 3.01" (76.56 mm)
Width: 4.15" (105.46 mm)
Depth: .95" (24.01 mm)
Mounting Hardware Included #6 Screws
Regulatory
Surface Mount Gasket creates an IP67 waterproof seal on unit face--temporary
immersion for 30 minutes.
Specifications
Indicates battery charger stage, alerts, and controls basic
battery charger functions
LED Indicators
• Charging: Quick check for green light confirms charging
• Charge Stage: Displays charging stage including PreFloat for each battery
• Equalize: Indicates when the charger is in equalization mode
• Fan Mode: Indicates charger’s internal fan mode
• Charge Output: Displays the percentage of output current for each battery.
Will also indicate maximum output setting when maximum output is adjusted
to accommodate for AC source limitations.
• Alert: Provides warning and alert status for quick diagnostics
Four Control Buttons
• Fan: User adjustable settings (OFF, LOW, or HIGH)
• Dim/ Alarm: Provides adjustment to brightness of LEDs on display as well
as Silence function for alarms.
• Output: User adjustable charger output when AC source limitations exist
that require lowering the AC current draw.
• Standby: Places P12 Battery Charger into standby mode
P12
Instructions
PN 7520 / PN 1521
BATTERY CHARGER REMOTE
1 of 4
Scan for
additional
product
information
Included Components
1. Mounting Screws: (4) #6 x 1" pan-head sheet metal screws (#2 Phillips screwdriver)
2. Cover
3. Remote Assembly
4. Mounting Gasket
5. 25 ft (7.6 m) Cat5e Cable
6. Dielectric Grease: Blue Sea Systems recommends using a high quality dielectric grease
for remote control connection. View the MSDS for the Dielectric
Grease at bluesea.com/P12
1
2
3
4
5
6
Register your P12 Remote Display at bluesea.com/warranty
Blue Sea Systems stands behind its products for as long as you own them. Blue Sea
Systems will replace or issue a credit for any of its products found to be defective in
materials or manufacture. P12 Battery Chargers and P12 Remote Displays are warranted
for a period of five years from the date of first purchase. No compensation will be allowed
for products not returned to Blue Sea Systems for analysis, nor will compensation be made
for labor required to replace any defective product. Please contact Customer Service for an
RMA number prior to shipping any product back to Blue Sea Systems. Blue Sea Systems
cannot accept liability for damage due to the use of the P12 Battery Charger.
“Date of first purchase” means:
1. The date on which the product was purchased by the first retail customer
2. The date on which the first retail customer purchases a vessel on which the product
was installed
Blue Sea Systems will (at its sole discretion) repair or replace any product which is:
1. Proven to be defective in materials or workmanship
2. Returned to Blue Sea Systems (or its agent) during the warranty period in accordance
with this warranty
The replacement battery charger may be new or refurbished in as-new condition. Such
repair or replacement will be the sole remedy by Blue Sea Systems under this warranty.
Any repaired or replacement product will be warranted in accordance with this warranty for
the unexpired balance of the warranty period on the original product.