Braun MC 100 - Manual (Page 2)

3
English
Read all instructions carefully before using this
product.
Important
● the blade 5 is very sharp! Take hold of the blade
by the plastic knob only. After using the blade,
always take it out of the workig bowl
4 first, before
removing the processed food.
● Your voltage must correspond to the voltage printed
on the bottom of the appliance. Connect to alter-
nating current only.
● Keep the appliance out of the reach of children.
● This appliance was constructed for household use
only to process the listed quantities.
● None of the parts (including the working bowl) are
microwave-proof. These parts should not be
washed in the dishwasher either.
● Braun electric appliances meet applicable safety
standards. Repairs on electrical appliances must
only be done by authorized service personnel.
Faulty, unqualified repair work may cause accidents
or injury to the user.
● The mains cable of this appliance can only be
changed by an official Service Dealer, since it
requires a special tool.
Specifications
● Voltage/wattage: See typeplate on the bottom of the
appliance.
● Opeating time and max. capacity: See processing
instructions.
This product conforms to the radio interference
supression requirements as laid down by the
Council Directive 82/499 EEC or 87/308 EEC.
Safety fuse
This unit is equipped with a self protecting system
which prevents damage to the motor in the case of
accidental overload and/or blockages. In those cases
the unit will automatically stop. Turn the appliance off
and leave for two minutes.
Afterwards, turn the appliance on again and continue
the operation. If the motor will not start, it has not
cooled off sufficiently. Turn the unit off again and wait
long enough for the motor to cool off thoroughly.
Store the appliance after use only after having turned
it off, or pull the plug out of the socket.
Description
1 Motor base
2 Switch
3 MC 200 only: Speed selector
4 Working bowl
5 Blade
6 Feed tube
7 Lid
8 Lid lock
9 Guide opening
j Central shaft
k Pusher
l Slicing insert
m Shredding insert
n Carrier disc
o a MC 200 only: Deflector
o b MC 200 only: Beater disc
p Cord storage compartment
Switch 2
0 = off
I = on
L = pulsator setting
For safety reasons, the motor turns on only if the lid
7
has been locked properly (see «Assembly»).
Assembly
Place the working bowl 4 on the central shaft j .
Ensure that the guide opening 9 on the working bowl
is aligned with the notches on the motor base. Turn the
working bowl slightly in the direction of the arrow until
it latches (A). (The lid lock
8 must slide into the
opening at the top of the motor base.)
● When using the blade 5 : Simply place the blade
on the central shaft j and press until it rests in
place (B).
Important: Always insert blade
5 before putting in
food.
● When using the slicer/shredder: Insert the cutting
insert you want (
l , m ) into the carrier disc n .
Insert the sharp side first; then snap the side with
the arrows in place (C).
Then place the carrier disc
n on the central
shaft j (D).
MC 200 only:
● When using the beater disc o b and deflector o a:
Place the beater disc in the working bowl first (H)
and then push the deflector over the two notches of
the working bowl so that it fits exactly into the
grooves inside the bowl (K).
Place the lid 7 on the working bowl 4 , coupling the
lock 8 on the lid 7 with the guide rail on the motor
base 1 . Turn the lid clockwise until it engages onto
the motor base 1 with an audible click (E). For
safety reasons, the motor will only operate if the lid
7 has been locked properly.
Processing in the working bowl
● Insert the food you want to process into the working
bowl only after you have inserted the blade
5 .
● Do not exceed the maximum capacity indicated in
the tables.
Depending on what you want to process, the
ingredients can either be put directly into the work-
ing bowl
4 or through the feed tube 6 even while
the motor is running (F).